Spectrasensors SS2100 - List of Figures

Hardware Installation and Maintenance Manual iii
LIST OF FIGURES
Figure 1–1. Schematic of a typical laser diode absorption spectrometer . . . . . . 1-4
Figure 1–2. Typical raw signal from a laser diode absorption spectrometer
with and without mirror contamination . . . . . . . . . . . . . . . . . . . . 1-5
Figure 1–3. Typical normalized absorption signal from a laser diode
absorption spectrometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
Figure 1–4. Typical normalized 2f signal; species
concentration is proportional to the peak height . . . . . . . . . . . . . . 1-7
Figure 1–5. SS2100 analyzer architecture. . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
Figure 1–6. H
2
S analyzer electronics control
board (AC) showing signal terminal block and alarm relays . . . . . . 1-9
Figure 1–7. H
2
S analyzer electronics control board (DC) showing
signal terminal block and alarm relays. . . . . . . . . . . . . . . . . . . . 1-10
Figure 2–1. Lifting points for the SS2100 H2S analyzer . . . . . . . . . . . . . . . . . 2-3
Figure 2–2. AC single phase (120 VAC or 240 VAC) connection
terminal block in analyzer electronics enclosure . . . . . . . . . . . . . . 2-7
Figure 2–3. AC connection terminal block for 120 VAC enclosure heater . . . . . . 2-8
Figure 2–4. Applying conduit lubricant . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
Figure 2–5. H
2
S analyzer mating terminal block (TB2) for connecting
signal cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12
Figure 2–6. Analyzer 4-20 mA board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14
Figure A–1. Outline and mounting dimensions (front view) of
SS2100 for H
2
S analyzer (fixed mount, conventional) . . . . . . . . . . A-3
Figure A–2. SCS schematic of SS2100 for H
2
S analyzer
(fixed mount, conventional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-4
Figure A–3. SCS schematic - Bill of Materials (fixed mount, conventional). . . . . A-5
Figure A–4. SCS schematic - solenoid/air-
actuated valves (fixed mount, conventional) . . . . . . . . . . . . . . . . A-6
Figure A–5. SCS schematic -Air-actuated valve, Liquid knock-
out (fixed mount, conventional) . . . . . . . . . . . . . . . . . . . . . . . . . A-7
Figure A–6. SCS schematic - high H2S purge (fixed mount, conventional) . . . . A-8
Figure A–7. Power and signal wiring diagram (fixed mount, conventional) . . . . A-9
Figure A–8. Wiring diagram - optional air actuated
valve (fixed mount, conventional). . . . . . . . . . . . . . . . . . . . . . . A-10
Figure A–9. Outline and mounting dimensions - optional heat trace /
high H2S purge (fixed mount, conventional) . . . . . . . . . . . . . . . A-11
Figure A–10. Outline and mounting dimensions (fixed mount, modular) . . . . . . A-12
Figure A–11. SCS schematic - optional heat trace and heater power
(fixed mount, modular) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-13
Figure A–12. SCS schematic - optional one-point solenoid validation
(fixed mount, modular) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-14
Figure A–13. Power and signal wiring (fixed mount, modular) . . . . . . . . . . . . . A-15