Spirax Sarco UFT32 User Manual

Local regulations may restrict the use of this product to below the conditions quoted.
In the interests of development and improvement of the product, we reserve the right to change the specification without notice. © Copyright 2019
Page 1 of 5
UFT32
Sealed Stainless Steel Ball Float Steam Trap
(for use with Pipeline Connectors)
TI-P146-05
CMGT Issue 6
Description
The UFT32 is an austenitic stainless steel maintenance free sealed ball float steam trap with an integral automatic air venting facility.
It is designed for differential steam pressures up to 32 bar.
When installed with a suitable pipeline connector the UFT32 can easily and simply be removed without breaking into the pipeline, thus
speeding up trap replacement with minimal system downtime. Pipeline connectors are available with screwed, socket weld and flanged
end connections.
Capsule
The BP99/32 capsule which is used in the UFT32 is suitable for use on 150 °C superheat @ 0 bar g and 50 °C superheat @ 32 bar g.
Standards
The body to cover welded joint complies with ASME Section IX and BS/EN 288.
This product fully complies with the requirements of the Pressure Equipment Directive (PED).
Certification
This product is available with certification to EN 10204 3.1.
Note: All certification/inspection requirements must be stated at the time of order placement.
Pipeline connector options
The UFT32 can be fitted to a variety of pipeline connectors including:
PC10HP Straight connector ASME 600 (TI-P128-10)
PC20 Straight connector with 'Y' type strainer ASME 300 (TI-P128-15)
IPC21 Straight connector with 'Y' type strainer and integral Spiratec sensor ASME 300 (TI-P128-15)
PC3 _ Straight connector with one piston isolation valve ASME 600 (TI-P128-02)
PC4 _ Straight connector with two piston isolation valves ASME 600 (TI-P128-03)
STS17. 2 Steam trap station (TI-P128-22)
See the relevant Technical Information sheet as listed above for details of the connections available for each pipeline connector.
UFT32 fitted to a PC4_ connector
UFT32 fitted to a PC3_ connector

Spirax Sarco UFT32 Specifications

General

Brand	Spirax Sarco
Model	UFT32
Category	Control Unit
Language	English

Summary

Description and Features

Product Description

Overview of the UFT32 steam trap's design and maintenance-free operation.

Capsule Specifications

Details on the BP99/32 capsule's suitability for specific superheat and pressure conditions.

Compliance and Standards

Information on welding compliance (ASME IX, BS/EN 288) and PED conformity.

Certification Availability

Notes on product certification to EN 10204 3.1 and ordering requirements.

Operating Limits and Conditions

Pressure/Temperature Limits

Graphical representation and text defining safe operating pressure and temperature ranges for the UFT32.

Body Design Conditions

Details of maximum allowable pressure, temperature, and operating pressure for the trap.

Differential Pressure Capability

Specifies the maximum differential pressure (APMX) the UFT32 is designed for.

Materials and Dimensions

Material Specifications

List of materials used for various parts of the UFT32 steam trap, including standards.

Physical Dimensions and Weight

Approximate dimensions (A, B, C) and weight of the UFT32 trap unit.

Installation, Ordering, and Capacity

Installation and Maintenance Guidance

Notes on installing the UFT32 with pipeline connectors and references to further instructions.

Disposal Information

Details regarding the recyclability and environmental impact of disposing of the UFT32 trap.

How to Specify and Order

Guidance on how to correctly specify and order the UFT32 trap and associated pipeline connectors.

Condensate Capacity Chart

Graph showing condensate capacity (kg/h) versus differential pressure for different UFT32 models.

Spare Parts and Torques

Available Spares

Identifies components available as spare parts for the UFT32 unit.

Ordering Spare Parts

Instructions on how to order replacement spare parts for the UFT32.

Tightening Torque Specifications

Recommended torque values for tightening connector screws during installation.