9
www.spokey.eu
www.spokey.pl
ASSEMBLY
PREPARATIONS
1. Before assembly make sure there is enough space.
2. Use the recommended tools.
3. Before assembly check if there are all the parts in the box.
It is recommended that product should be assembled by at least two people
to avoid injuries.
Most of the assembly equipment listed here has been packed separately,
but some elements come preassembled in certain assembly parts. If it is
required, dissassemble them and assemble again.
Read the instructions of all assembly steps and familiarize with all the
devices installed.
ASSEMBLY INSTRUCTIONS (DRAWINGS – P. 61-64)
ATTENTION! Do not connect the device to the power source until you finish
the assembly.
STEP 1 Open the box, take out the parts. Place the main frame on the floor.
STEP 2 Gently pull the console in the direction shown by the arrow. Make
sure that the cables are not tightened. Use bolt (32) and Allen key #5 (21),
to attach the cables console cover (108)
STEP 3 Pull the part A-1 in the direction shown by the arrow. Place the
main frame (A) in a vertical position.
STEP 4 Turn the part A-3 in the direction of the arrow
STEP 5 Press the part A-1 so as to point it down, then raise the left and
right column of the treadmill (A-2) up, in the direction of the arrow.
STEP 6 1. Turn the handle with the treadmill's incline adjustment buttons
(B) clockwise, to block it in the main frame.
2. Repeat the same procedure with the holder on which the speed
adjustment buttons (C) are located.
FOLDING AND TRANSPORT OF THE TREADMILL
Don't try to move the treadmill if it's not folded and locked. Make sure that
the plug is disconnected from power supply.
To set the treadmill in the vertical position it is necessary to fold the console
handles. Then – making sure the element A-1 remains in the position as in
the Figure – turn the part A-2 in the direction of the main frame (A) until you
hear a click. Then lift the treadmill belt in the direction indicated by the arrow
- to the position indicated in the Figure.
To unfold the treadmill, place the main frame (A) on the ground and unfold
the component A-1. Then pull up the part A-2 until you hear a click. Turn
the console handles (B, C) to the position indicated in the Figure. Please
refer to the drawing 1 (p. 65).
ATTENTION: Folded treadmill cannot be operated and utilized. Stop the
treadmill belt before folding the equipment. Folded treadmill should be
disconnected from power supply. Don't start the treadmill when it's folded.
To move the treadmill, raise it gently onto the rear transport rolls and move
it to the desired location, holding on both sides.
ATTENTION: Before transporting the treadmill make sure that it is
disconnected from power supply. The device should always be transported
by two persons..
MAINTANCE
Caution: before cleaning / lubrication you must take out the power plug from
a socket.
For cleaning the exercise machine, do not use any abrasive detergents.
Use a soft, damp cloth to remove dirt and dust.
The monitor (power supply dome) should be cleaned only with a dry cloth.
The equipment should be stored in dry places in order to protect it from any
moisture and corrosion.
Use a soft, damp cloth to wipe off the edges of the treadmill belt, and the
space between the treadmill belt and the frame edges. Clean the edge of
the belt on its bottom side also. Clean the upper part of the belt with a brush
and soap water once a month.
NOTE: Before you start using the treadmill again, wait until the equipment
is completely dry.
Vacuum under the equipment at least once a month to prevent dust from
accumulating.
Once a year, it is recommended to remove the black cover of the engine in
order to remove any dust that may accumulate there.
NOTE: The level of equipment operational safety can be maintained only
by regular inspections checking for any damage and wear.
Connecting elements are the most vulnerable to any wear..
BELT TENSION ADJUSTMENT
Belt Tension Adjustment-It is very important for joggers and runners in
order to provide a smooth, steady running surface. Adjustment must be
made from the right and left rear roller in order to adjust tension with the
Hexagonal Wrench provided in the parts package. The adjustment bolt is
located at the end of the rails as noted in diagram below.
Note: Adjustment is thru the small holes on the end caps.
Tighten the rear roller only enough to prevent slippage at the front roller.
Turn both the right and left bolt clockwise reasonably and inspect for proper
tension. When an adjustment is made to the belt tension, you must also
make a tracking adjustment to compensate for the change in belt tension.
DO NOT OVERTIGHTEN - Over tightening will cause belt damage and
premature bearing failure.
BELT TRACKING ADJUSTMENT (PICTURE, P. 65)
This treadmill is designed to keep the belt reasonably centred while in use.
It is normal for some belts to drift near one side while the belt is running
with no one on it. After a few minutes of use, the belt should have a
tendency to centre itself. If during use, the belt continues to move toward
one side, adjustments are necessary. The procedures are as below:
▲ First set speed at lowest position.
▲ Second check the belt shifts to which side.
If the belt shifts to right, tighten the right bolt and loosen the left bolt by
using 6mm Hexagonal Wrench, until the belt is centered itself; if belt shifts
to left, tighten the left bolt and loosen the right bolt by using 6mm Hexagonal
Wrench, until the belt is centered. When adjusting the belt using the 6 mm
Hexagonal Wrenches, it is important to adjust the belt in half turn
increments. Over adjusting the belt can cause damage to the mat.
HOW TO CHECK THE RUNNING MAT FOR PROPER LUBRICATION (PICTURE, P. 65)
Disconnect the main power supply.
Fold the treadmill up into the storage position.
Feel the back surface of the running mat.
BELT/DECK/ROLLER LUBRICATION
The mat/deck friction may play a major role in the function and life of your
treadmill and that is why we recommend you constantly lubricate this
friction point to prolong the life time of your treadmill.
You should apply the lubrication after approximately the first 20 hours of
operation. We recommend lubrication of the deck every 30 days.
See below procedures for lubricating:
Use a soft, dry cloth to wipe the area between the belt and deck.
Spread lubricant onto the inside surface of belt and deck evenly (make sure
the machine is turned off and power is disconnected).
Periodically lubricate the front and rear rollers to keep them at their peak
performance.
If the treadmill belt/deck/roller is kept reasonably clean it is possible to
expect over 120 hours before additional re-lubing is necessary
To Next Page
Loading...
