ST NUCLEO-U575ZI-Q - Mechanical Drawing; Figure 6. STM32 U5 Nucleo-144 Board Mechanical Drawing (in Millimeters)

49 pages

To Next Page

To Previous Page

6.2 Mechanical drawing

Figure 6. STM32U5 Nucleo-144 board mechanical drawing (in millimeters)

UM2861

Mechanical drawing

UM2861 - Rev 5

page 12/49

Main Page

Figure 1. STM32U5 Nucleo-144 Board1
Features2
Ordering Information3
Products and Codification3
Table 1. Ordering Information3
Table 2. Codification Explanation3
Development Environment4
System Requirements4
Development Toolchains4
Conventions5
Table 3. ON/OFF Convention5
Quick Start6
Getting Started6
Default Board Configuration6
Table 4. Default Jumper Configuration6
Figure 2. Default Board Configuration7
Table 5. Jumper Configuration8
Hardware Layout and Configuration9
Figure 3. Hardware Block Diagram9
STM32U5 Nucleo-144 Board Layout10
Figure 4. STM32U5 Nucleo-144 Board Top Layout10
Figure 5. STM32U5 Nucleo-144 Board Bottom Layout11
Mechanical Drawing12
Figure 6. STM32U5 Nucleo-144 Board Mechanical Drawing (in Millimeters)12
Embedded STLINK-V3E13
Description13
Drivers13
STLINK-V3E Firmware Upgrade13
Table 6. USB Micro-B Connector (CN1) Pinout13
Using an External Debug Tool to Program and Debug the On-Board STM3214
Figure 7. Connecting an External Debug Tool to Program the On-Board STM32U514
Table 7. STDC14/MIPI10 Debug Connector (CN5) Pinout15
Figure 8. STDC14/MIPI10 Debug Connector (CN5)15
Power Supply and Power Selection16
External Power Supply Input16
Table 8. Power Sources Capability16
Figure 9. JP6 [1-2]: 5V_STLK Power Source17
Figure 10. JP6 [3-4]: 5V_VIN Power Source18
Figure 11. JP6 [5-6]: 5V_EXT Power Source19
Figure 12. JP6 [7-8]: 5V_USB_C Power Source20
Figure 13. JP6 [9-10]: 5V_CHGR Power Source21
Programing/Debugging When the Power Supply Is Not from STLINK-V3E (5V_STLK)22
Power Supply Output22
Internal Power Supply22
MCU Power Supply23
Table 9. MCU Power Supplies23
VDD_MCU IDD Measurement24
Leds24
Push-Buttons25
OSC Clock Sources26
LSE: OSC 32 Khz Clock Supply26
OSC Clock Supply27
Reset Sources27
Virtual COM Port (VCP)28
Bootloader28
Table 10. USART1 Connection28
Table 11. LPUART1 Connection28
USB Type-C ® FS/HS29
USB FS/HS Device29
Ucpd29
Table 12. Hardware Configuration for the USB Interface29
Table 13. Hardware Configuration for the UCPD Feature30
USB Type-C ® Connector31
Table 14. USB Type-C ® Connector (CN15) Pinout31
Figure 14. USB Type-C ® Connector (CN15) Pinout31
Extension Connectors32
Zio Connectors Supporting ARDUINO ® uno V332
Figure 15. Zio Connectors Supporting ARDUINO ® uno V332
Table 15. ARDUINO ® -Included Zio Connector (CN7) Pinout33
Table 16. ARDUINO ® -Included Zio Connector (CN8) Pinout33
Table 17. ARDUINO ® -Included Zio Connector (CN9) Pinout34
Table 18. ARDUINO ® -Included Zio Connector (CN10) Pinout34
ST Morpho Headers (CN11 and CN12)36
Figure 16. ST Morpho Connector36
Table 19. ST Morpho Connector Pin Assignment37
Solder Bridge Configuration for the Expansion Connector38
Table 20. Solder Bridge Configuration38
STM32U5 Nucleo-144 Board (MB1549) Product Information40
Product Marking40
STM32U5 Nucleo-144 Board (MB1549) Product History41
Table 21. Product History41
Board Revision History42
Table 22. Board Revision History42
Federal Communications Commission (FCC) and ISED Canada Compliance43
Statements43
FCC Compliance Statement43
ISED Compliance Statement43
Revision History44
Table 23. Document Revision History44
Table of Contents45
List of Tables47
List of Figures48

ST NUCLEO-U575ZI-Q - Mechanical Drawing; Figure 6. STM32 U5 Nucleo-144 Board Mechanical Drawing (in Millimeters)

Table of Contents

Related product manuals