This document describes the Stanley Indoor Remote Control, model BNC-60/U116R, which consists of a receiver and a remote control for operating indoor appliances.
Function Description
The Stanley Indoor Remote Control system allows users to wirelessly control an appliance plugged into the receiver. The receiver plugs into a standard grounded outlet, and the appliance then plugs into the receiver. The remote control, powered by a 12V/23A battery, features ON/OFF buttons to toggle the power to the connected appliance. The system is pre-programmed for immediate use, but its configuration can be customized to meet specific needs. The receiver also has a "learning and ON/OFF" button for programming and resetting the unit.
Important Technical Specifications
- Receiver:
- 1 Grounded outlet
- Rated: 125VAC / 60Hz / 10A / 1250W Resistive
- 5A / 625W Tungsten
- Remote Control:
- Transmission frequency: 433.92Mhz
- Remote battery: 12V/23A (included)
- Maximum Load Current: Do not exceed 10A (approximately 1250W).
Usage Features
Setup:
- Install Battery: Insert one 12V/23A battery into the remote control's battery compartment, ensuring correct polarity.
- Plug in Receiver: Plug the receiver into a grounded wall outlet. Ensure the receiver is turned on.
- Connect Appliance: Plug your device or appliance into the grounded outlet on the receiver.
- Operate: Press the ON/OFF buttons on the remote control for the respective channel to operate the unit.
Programming (Customization):
The receiver is pre-programmed, but you can customize its configuration.
- Remove and Re-plug Receiver: Unplug the receiver from the power socket, then plug it back in.
- Enter Learning Mode: Press and hold the "learning and ON/OFF" button on the receiver until its indicator light starts to flash.
- Pair with Remote: Release the "learning and ON/OFF" button on the receiver. Then, press and hold the corresponding "ON" button on the remote control until you hear a click.
- Confirmation: The indicator light on the receiver will stop flashing, indicating successful pairing.
Resetting the Receiver:
If you wish to unpair a receiver from the remote or if the unit becomes unresponsive, you can reset it.
- Remove Receiver: Unplug the receiver from the power socket.
- Press and Hold Button: Press and hold the "learning and ON/OFF" button on the receiver.
- Re-plug While Holding: While still holding the button, plug the receiver back into the power socket and wait for the indicator light to flash.
- Release Button: Once the indicator stops flashing, you may release the button. The reset process is complete.
- Reprogram: You can program the outlet again after resetting.
Troubleshooting:
If the receiver does not respond to the remote control, follow these steps:
- Check Remote Battery: Verify if the remote control's battery is low and needs replacement.
- Receiver Placement: Ensure the receiver is correctly plugged into the power socket.
- Air Circulation: Make sure the receiver is used in an area with proper air circulation to prevent overheating.
- Reset and Program: Reset and reprogram the unit as described above.
Important Safety and Usage Notes:
- Ensure the battery and receiver are installed firmly and correctly for safe operation.
- This unit is for indoor use only.
- Avoid exposure to high-temperature sources, strong sunlight, and moisture.
- The receiver performs best when used in a space with good air circulation.
- Do not exceed the maximum load current of 10A (approximately 1250W).
Maintenance Features
Battery Replacement:
- Regularly change the battery in the remote control for best performance.
- If the receiver is unresponsive or the LED indicator on the remote control becomes dim, the battery should be replaced.
- Always dispose of old batteries properly, considering environmental guidelines.
Warranty:
The product comes with a Three-Year Limited Warranty.
- First Year: If the unit fails due to a defect within the first year from the date of purchase, it can be exchanged where purchased or shipped prepaid with proof of purchase to The NCC, 1840 McDonald Avenue, Brooklyn, New York 11223.
- Second or Third Year: Units failing during the second or third year from the date of purchase must be shipped prepaid with proof of purchase to The NCC for replacement.
- Exclusions: This warranty excludes normal wear and tear and damage resulting from accident, alteration, or misuse.
- Legal Rights: This warranty provides specific legal rights, and other rights may vary by state.
- Replacement: For warranty replacement, the unit must have been purchased from an authorized reseller.
FCC Compliance:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
Need help?
General
To Next Page
