Stanley NB08PT-18 User Manual (English)

Other manuals for Stanley NB08PT-18

Instruction Manual626 pages

Service Manual31 pages

Questions and Answers:

J
Joan MeyersAug 20, 2025
Why does my Stanley Rivet Tools power not turn on?
- J
  Jessica MillerAug 20, 2025
  If your Stanley Rivet Tool's power isn't turning on, there are several potential causes: * The battery might not be fully attached. Try removing the battery and re-inserting it, then reset the tool. * The battery could be low on charge. Make sure to fully charge the battery. * The battery may be malfunctioning, in which case you should replace it. * There may be a trigger module malfunction.
J
Jason RamirezAug 22, 2025
What to do if my Stanley Rivet Tools screen freezes at the logo?
- L
  Linda CortezAug 22, 2025
  If the screen on your Stanley Rivet Tools freezes at the Stanley Engineered Fastening Logo, it could be due to a few reasons: * A data reading error. Try removing and reinserting the battery, then press the trigger to turn the tool on. * Smart screen malfunction. * Trigger module malfunction. * Broken setting data. In this case, try restoring the tool to its factory settings.
K
Kristi SalasAug 25, 2025
What to do if Stanley Rivet Tools do not function when mandrel was pushed?
- S
  Scott MeadowsAug 25, 2025
  If your Stanley Rivet Tools doesn't function when the mandrel is pushed, here are some possible causes and solutions: * The screen might not be on the home screen (it might be on the counter screen). Get the screen back to the home screen by touching the “Back home” icon. * The screen may be malfunctioning, freezing, or all white. Try removing and reinserting the battery, then press the trigger to turn the tool on. Alternatively, set the tool to default. * An alarm message is being shown with a beep sound. Reset the alarm. * The setting data is broken. Restore the tool to its factory settings. * There is a radio communication error. Restore to factory settings. * The tool is already operating. Continue with fastening or enforced spin off.
L
Linda JamesAug 26, 2025
Why Stanley Power Tool does not turn on?
- C
  Casey HudsonAug 26, 2025
  If your Stanley Power Tool does not turn ON, there are several potential causes: 1. The battery may not be fully attached. Try removing the battery and re-inserting it, then reset the tool. 2. The battery might not be fully charged. Ensure the battery is adequately charged. 3. The battery could be defective. Consider replacing the battery. 4. There may be a trigger module malfunction. In this case, it is best to contact a local service center.
C
Cory JohnsonAug 27, 2025
What to do if Stanley NB08PT-18 Power Tool does not count correctly?
- M
  Matthew DavidsonAug 27, 2025
  If your Stanley Power Tool is not counting correctly, or counts even when it does not set a nut, consider the following: 1. The fastening force might be too low. Try resetting the stroke and force. Note that for aluminum M3 at extremely low force, it might not count in some cases. 2. The battery may not be fully charged. Check the battery charge level and charge if necessary. 3. The battery could be malfunctioning. Consider replacing it. 4. The setting files might be corrupted. Restore to factory settings. 5. There may be a calibration issue. Contact a local service center.
R
robertscottAug 29, 2025
What to do if Stanley NB08PT-18 screen freezes at Stanley Engineered Fastening Logo?
- P
  Phillip SmithAug 29, 2025
  If the screen on your Stanley Power Tool freezes at the Stanley Engineered Fastening Logo, here are some possible solutions: 1. It could be due to a data reading error. Remove and reinsert the battery, then press the trigger to turn it ON. 2. The smart screen might be malfunctioning. Contact a local service center. 3. The trigger module could be malfunctioning. Contact a local service center. 4. The setting data might be broken. Restore the tool to its factory settings.
R
Rachel WellsAug 31, 2025
What to do if Stanley NB08PT-18 does not operate when trigger switch is pressed?
- I
  Ian GrahamAug 31, 2025
  If your Stanley Power Tool does not operate when the trigger switch is pressed: 1. Ensure the screen is on the home screen and not the counter screen. Touch the “Back home” icon to return to the home screen. 2. If the screen is malfunctioning, freezing, or all white, remove and reinsert the battery, then press the trigger to turn it on. Alternatively, set the tool to default. If the problem persists, contact a local service center. 3. Ensure the tool is in operating mode.
T
Tyler SpenceSep 2, 2025
What to do if Stanley Power Tool do not function when mandrel was push?
- A
  Alexander WilsonSep 2, 2025
  If your Stanley Power Tool does not function when the mandrel is pushed, consider the following: 1. Ensure the screen is on the home screen, not the counter screen. Touch the “Back home” icon to return to the home screen. 2. If the screen is malfunctioning, freezing, or all white, remove and reinsert the battery, then press the trigger to turn it ON. Alternatively, set the tool to default. If the issue continues, contact a local service center. 3. If an alarm message is shown with a beep sound, reset the alarm. 4. If the setting data are broken, restore to factory settings. 5. In case of a radio communication error, restore to factory settings. If the problem persists, contact a local service center. 6. If the tool is already operating, continue with fastening or enforce spin off.
J
Jessica WalkerSep 3, 2025
Why Stanley Power Tool has insufficient or excessive fastening stroke?
- V
  Victor BarrySep 3, 2025
  If you observe insufficient or excessive fastening stroke on your Stanley Power Tool: 1. The setting value of fastening stroke or fastening load may be inappropriate. Use an appropriate setting value. 2. There might be a malfunction of the control part. Set up to factory default condition. If it does not return, contact a local service centre. 3. The setting file might be malfunctioning. Restore to factory settings. 4. The trigger module or screen module could be malfunctioning. Contact a local service center.
J
judithsellersSep 5, 2025
Why Stanley NB08PT-18 Power Tool assumed fully charge battery fasterned low number of nuts?
- D
  Dustin TaylorSep 5, 2025
  If you find that a fully charged battery on your Stanley Power Tool fastens a low number of nuts: 1. The battery might not be fully charged. Check the battery level and fully charge the battery. 2. The battery could be malfunctioning. If power consumption is faster than usual, replace the battery.