Stanton SK-2 User Manual

SK TWO Professional performance mixer
STANTON MAGNETICS, LLC
2821 Evans St. Hollywood, FL 33020
(954) 929-8999 - Fax: (954) 929-0333
info@stantonmagnetics.com
OWNER’S M A N U A L
FA DER C LEA N I N G
The SK TWO faders may need lubrication from time to time. This will extend the
fader life and eliminate any potential damage due to extended heavy usage.
R E P L AC E M E N T PA RTS
To replace the cross or channel faders, follow steps 1 and 2 of the cleaning
instructions. The following replacement parts are available from Stanton or your
local Stanton dealer.
ROTATING AND REPLACING THE INPUT TOGGLE SWITCHES
Cleaning Instructions
1. Remove the 3 fader knobs and 4 screws
located in the corners of the PROTEKT™
(see “ ” inside) panel
and take the panel off the mixer.
2 . Remove the fader to be cleaned by
unscrewing the 2 outer screws (removing
the 2 inner screws will detach the fader
from the fader plate) and disconnect the
cable coming from the mixer.
3. Spray a small amount of cleaner or
lubricant into both ends of the fader and
slide the fader back and forth a few times
to spread the fluid evenly throughout the
fader.
4. Shake and wipe off excess fluid before
re-assembling the fader.
PL-SK2 Two way input toggle switch
3PL-SK2 Three way input toggle
switch with FLASH™
LF-SK2 Channel input fader
CF-SK2 Crossfader
PP-SK2 PROTEKT™ panel
PS-18US US Power Supply (110v)
PS-18EU European Power Supply (220v)
PS-18UK UK only Power Supply (240v)
ROTATING I NST RU C TI O N S
1 . Remove the PROTEKT™ panel
2. Remove the 2 outer screws from the
round plate (removing the 2 inner screws
will detach the switch from the plate)
3. Rotate the plate to the desired position
and tighten the screws back in the top and
bottom holes
R E PLAC I N G I N ST RU C TI O N S
1. Remove the PROTEKT™ panel
2. Remove the 2 outer screws from the
round plate (removing the 2 inner screws
will detach the switch from the plate)
3. Remove the switch assembly and dis-
connect the cable coming from the mixer.
4. Set the replacement switch assembly in
the desired position and place the screws
back in the top and bottom holes.
© 1999, Stanton Magnetics, LLC

Stanton SK-2 Specifications

Inputs and Outputs

line inputs	2 (RCA), 150 mV / 27K ohm
phono inputs	2 (RCA), 3 mV / 47K ohm
DJ mic input	1 (1/4 inch), 2.45 mV / 3K ohm
master output	1 (1/4” TRS Balanced/RCA unbalanced), 775 mV / 1K ohm
record output	1 (RCA), 245 mV / 10K ohm
headphone output	1 (1/4 inch), 32 - 200 ohms recommended

Audio Specifications

frequency response	20 Hz - 20 kHz, +/- 2 dB
tone control	+ 9/-26 dB (Hi, Mid, Low)
mic tone	Hi/Mid/Lo +/-12 dB
gain control	0-20dB
S/N ratio	Less than 70dB
T.H.D	less than 0.2%

Weight and Dimensions

dimensions (LxWxD)	12 [3/8]” x 10 [1/4]” x 4” (314 x 260 x 102 mm)
weight	7 lbs (3.2 Kg)

Summary

Fader Cleaning and Maintenance

Cleaning Instructions

Step-by-step guide for cleaning faders on the SK TWO mixer to extend life and prevent damage.

Replacement Parts List

List of available replacement parts for cross and channel faders from Stanton.

Input Toggle Switches

Rotating Instructions

Instructions for rotating the input toggle switches to a desired position on the mixer.

Replacing Instructions

Steps for removing and replacing input toggle switches on the mixer.

Troubleshooting and Safety

Troubleshooting Guide

Common problems and their solutions for the Stanton SK TWO mixer.

Important Safety Precautions

Essential safety advice and handling instructions to prevent damage and ensure safe operation.

Mixer Functions and Design

Description of Mixer Functions

Detailed explanation of all controls and their functions on the SK TWO mixer.

Special PROTEKT™ Panel

Information about the PROTEKT™ panel's design and reversible nature for component access.

Technical Specifications and Warranty

Technical Specifications

Comprehensive technical specifications for the Stanton SK TWO mixer.

Warranty and Registration

Details on the product warranty, its terms, and online registration requirements.