What to do if my stertil-KONI ST 1075-FWF Lifting Systems has no battery power?
If your Stertil-KONI Lifting Systems has no battery power, try these solutions: * Charge the batteries using the provided mains cable, avoiding external booster chargers. It is also recommended to have the batteries checked by a specialist. * Check the main fuse located above the batteries. * Ensure the main switch is set to the ON position.
What to do if my Stertil-KONI Lifting Systems column lift cannot be raised?
If your Stertil-KONI column lift cannot be raised, consider the following: * Check the main fuse above the batteries and have the batteries inspected by a battery specialist if there's no battery power. * If the oil level is too low but the motor is running, top up the oil. * If air is present in the hydraulic pump (possible after the tank has been empty), select [SINGLE] operation and press the [UP] button until the column lift rises, but no more than 1 minute.
What to do if my Stertil-KONI Lifting Systems has no control voltage?
If your Stertil-KONI lifting system has no control voltage: * Set the main switch to ON. * The controller has multi-fuse circuit breakers. After they have cooled down, they switch back on again automatically. If the fault occurs again, contact technical services. * Follow the normal operation procedures as described in the Operation Manual. If the fault occurs again, contact technical services.
What to do if my stertil-KONI ST 1075-FWF battery is flat and movements are impossible?
If your Stertil-KONI Lifting Systems has a flat battery and you can't perform any movements: * Set the system to charging if it happens after more than 15 movements on a single battery charge. * Charge the batteries of the column if one of the columns was not charged in time.
What to do if my Stertil-KONI Lifting Systems lowering motion stops and the lower stop limit message appears?
If the lowering motion stops and the message 'The lower stop limit has been reached' appears on the screen of your Stertil-KONI Lifting Systems, raise the columns approximately 4" and remove any obstacles. The column lifts can now be lowered further. Do not forget to press the [UNLOCK] button first.
Why does my stertil-KONI ST 1075-FWF raising motion stop and show a maximum height reached message?
If the raising motion stops and the message 'Maximum programmed height reached' appears on the screen of your Stertil-KONI Lifting Systems, it means one of the columns has reached its highest position. In this case, lower the columns.
What happens if foot guard limit has been reached in stertil-KONI ST 1075-FWF Lifting Systems?
If the foot guard limit has been reached on your Stertil-KONI Lifting Systems, lower the columns to reach ground level.
What to do if emergency switch is pressed on stertil-KONI ST 1075-FWF?
If the emergency switch is pressed on your Stertil-KONI Lifting Systems, it likely indicates a dangerous situation. Release the switch only when it is safe to do so.
What to do if Service Mode (PCB Main button pressed) is active on stertil-KONI ST 1075-FWF Lifting Systems?
If the Service Mode is active on your Stertil-KONI Lifting Systems (PCB Main button pressed), release the buttons on the control board and start up again.
What to do if stertil-KONI ST 1075-FWF shows error in another column?
If your Stertil-KONI Lifting Systems shows an error in another column, check other columns for system errors.
Identifies electrical, mechanical, and fall hazards associated with the lift.
Provides overarching safety guidelines and importance of safety.
Covers personnel qualifications, safety warnings, and instructions.
Specific safety instructions for operation and maintenance.
Describes built-in safety features like emergency stop and lock-out.
Details the critical safety procedure for energy isolation during servicing.
Provides key technical data, specifications, and model details.
Covers recommendations, safety, and preparations for maintenance.
Covers annual servicing and regular preventive maintenance procedures.
Covers general safety, knowledge, repair requests, communication, and parts.
Explains parts list columns and procedures for ordering replacement parts.
Explains how system messages are displayed and their meaning.
Details information messages, possible causes, and solutions.
Lists fault messages, their causes, and recommended solutions.
Describes error messages that lock out further operations.
Troubleshooting guide for common faults like lift not raising or lowering.
Provides an overview of the main assemblies and their components.
General| Brand | stertil-KONI |
|---|---|
| Model | ST 1075-FWF |
| Category | Lifting Systems |
| Language | English |
To Next Page