What to do if my Stertil-KONI Lifting Systems has no battery power?
If your Stertil-KONI Lifting Systems has no battery power, try these solutions: * Charge the batteries using the provided mains cable, avoiding external booster chargers. It is also recommended to have the batteries checked by a specialist. * Check the main fuse located above the batteries. * Ensure the main switch is set to the ON position.
What to do if my Stertil-KONI Lifting Systems column lift cannot be raised?
If your Stertil-KONI column lift cannot be raised, consider the following: * Check the main fuse above the batteries and have the batteries inspected by a battery specialist if there's no battery power. * If the oil level is too low but the motor is running, top up the oil. * If air is present in the hydraulic pump (possible after the tank has been empty), select [SINGLE] operation and press the [UP] button until the column lift rises, but no more than 1 minute.
What to do if my Stertil-KONI Lifting Systems has no control voltage?
If your Stertil-KONI lifting system has no control voltage: * Set the main switch to ON. * The controller has multi-fuse circuit breakers. After they have cooled down, they switch back on again automatically. If the fault occurs again, contact technical services. * Follow the normal operation procedures as described in the Operation Manual. If the fault occurs again, contact technical services.
What to do if my Stertil-KONI Lifting Systems battery is flat and movements are impossible?
If your Stertil-KONI Lifting Systems has a flat battery and you can't perform any movements: * Set the system to charging if it happens after more than 15 movements on a single battery charge. * Charge the batteries of the column if one of the columns was not charged in time.
What to do if my stertil-KONI ST 1085-VFWA Lifting Systems lowering motion stops and the lower stop limit message appears?
If the lowering motion stops and the message 'The lower stop limit has been reached' appears on the screen of your Stertil-KONI Lifting Systems, raise the columns approximately 4" and remove any obstacles. The column lifts can now be lowered further. Do not forget to press the [UNLOCK] button first.
Why does my stertil-KONI ST 1085-VFWA raising motion stop and show a maximum height reached message?
If the raising motion stops and the message 'Maximum programmed height reached' appears on the screen of your Stertil-KONI Lifting Systems, it means one of the columns has reached its highest position. In this case, lower the columns.
What happens if foot guard limit has been reached in stertil-KONI ST 1085-VFWA Lifting Systems?
If the foot guard limit has been reached on your Stertil-KONI Lifting Systems, lower the columns to reach ground level.
What to do if emergency switch is pressed on Stertil-KONI Lifting Systems?
If the emergency switch is pressed on your Stertil-KONI Lifting Systems, it likely indicates a dangerous situation. Release the switch only when it is safe to do so.
What to do if Service Mode (PCB Main button pressed) is active on Stertil-KONI Lifting Systems?
If the Service Mode is active on your Stertil-KONI Lifting Systems (PCB Main button pressed), release the buttons on the control board and start up again.
What to do if stertil-KONI ST 1085-VFWA shows error in another column?
If your Stertil-KONI Lifting Systems shows an error in another column, check other columns for system errors.
Covers potential hazards including electrical, mechanical, and fall risks.
Details importance of safety, procedures, warnings, personnel, and instructions.
Describes safety mechanisms like emergency stop, and safety signs.
Explains procedures to prevent energy application during servicing.
Lists key technical data like lifting capacity, power, and dimensions.
Specifies the maximum load the lift can handle and its safety features.
Describes the electrically driven hydraulic column lift system components.
Details how the system ensures synchronized lifting and height control.
Describes the components of the hydraulic power unit.
Explains the main structural parts of the mobile column lift.
Details the functions of the control panel and emergency stop.
Describes the mechanism used for relocating the column lift.
Describes the mechanical safeguard that prevents falling if hydraulic pressure fails.
Provides step-by-step instructions for unpacking and initial setup.
Covers preparations, safety, waste disposal, and record-keeping for maintenance.
Lists essential monthly inspection and lubrication tasks.
Outlines requirements for yearly inspections by authorized technicians.
Details lubrication, hydraulic oil replacement, and safety feature checks.
Covers user settings, shop configuration, and user administration.
Details procedures for managing users, setting the clock, and height limits.
Outlines safety, knowledge, repair requests, communication, and parts for repairs.
Provides steps for removing/installing cylinders and adjusting mechanisms.
Explains the structure and titles of the parts list.
Guides on ordering replacement parts with necessary information.
Provides general advice for diagnosing and resolving faults.
Explains system messages displayed during operation, like lowering stops.
Lists system messages, their causes, and solutions for bringing the system back to normal status.
General| Brand | stertil-KONI |
|---|---|
| Model | ST 1085-VFWA |
| Category | Lifting Systems |
| Language | English |
To Next Page