STIEBEL ELTRON PER 18/21/24 - Display and Time Settings; Automatic Water Volume Control; Wireless Remote Control Management

OPERATION
Settings
www.stiebel-eltron.com PER 18/21/24 | 7
ENGLISH
4.2.5 Activating/deactivating the Wellness comfort function
You can permanently program a Wellness comfort function which,
after water has been drawn for three minutes, reduces the temper-
ature by 10°C and then increases it again after 10 seconds. After
a further 10seconds, the temperature is lowered again by 10°C
and then raised again after 10seconds. This temperature change
continues for the entire period that water is being drawn.
Press the ECO button for
3seconds
38°C
Press the ECO button briefly
several times
OFF
Select "OFF"/"ON" OFF:
ON:
deactivated
activated
4.2.6 Activating/deactivating/adjusting the automatic water
volume control
You can set the automatic water volume control function so that the
flow rate is reduced to approx.4l/min once a specified volume has
been drawn off. This enables you to influence the amount of water
drawn as well as the duration of a shower. The selected automatic
water volume control only applies to the next draw-off.
Press the ECO button for
3seconds.
38°C
Press the ECO button briefly
several times.
OFF
Select "OFF"/"ON" OFF:
ON:
deactivated
activated
When set to "ON", briefly press
the ECO button
80 l
Adjust the water volume
5-200 l
e.g. 150 l
4.2.7 Selecting the second line in the display
You can select what additional information is displayed in the sec-
ond line:
l/min Flow rate
kWh Energy consumption (you can set the values of these con-
sumption indicators to zero)
m³ Water volume (you can set the values of these consumption
indicators to zero)
Clock Time (if the power supply has been interrupted you will
need to reset the clock)
Press the ECO button for
3seconds
38°C
Press the ECO button briefly
several times
Select the display value for the
second line
Selected display
Setting the "energy consumption and water volume" consumption
indicator to zero.
In the INFO menu, press but-
ton1 and button2 simultane-
ously when the corresponding
consumption value appears in
the display
0
4.2.8 Setting the time
Press the ECO button for
3seconds
38°C
Press the ECO button briefly
several times
Set the time E.g. 12:15
Please note:
Reset the time after
a power supply in-
terruption.
4.2.9 Wireless remote control – checking, registering,
deregistering
The appliance can be controlled remotely by means
of a wireless remote control. The transmitter is water-
proof and can also be used whilst showering or bath-
ing. Up to four wireless remote controls can be combined.
The wireless remote control enables you to control the temperature
of the appliance remotely from another location (e.g. from the
kitchen sink).
The wireless remote control has four buttons for selecting the tem-
perature (38°C and 55°C are fixed settings; plus and minus button
for changing the temperature in 0.5°C stages). When a signal is
being sent to the appliance, the red LED on the wireless remote
control lights up.
If you press any button on the remote control while the appliance
is in ECO mode, the ECO function is cancelled for the next draw-off.
ECO mode is resumed two minutes after the draw-off.
If the appliance is in standard mode, a constant temperature can
be selected via the wireless remote control.
Wireless remote control check on the appliance
Press the ECO button for
3seconds 38°C
Press the ECO button briefly
several times
rc 1-4
Number of registered
wireless remote controls
(rc: remote control)
Registering a wireless remote control at the appliance
Press the ECO button for
3seconds 38°C
Press the ECO button briefly
several times
rc 1
Press button1: Self-learning
phase is activated.
Press any button on the wire-
less remote control.
Bar graph is shown.
Green LED flashes.
rc 2
Bar graph display goes
out.
Wireless remote control is
recognised
Deregistering a wireless remote control from the appliance
Press the ECO button for
3seconds 38°C
Press the ECO button briefly
several times
rc 2
In "rc" mode, press button2 rc 0: All wireless remote
controls are deregistered