To Next PageTo Next PageWhy does my Stiga F 72 FL engine stop while working and the lamp flashes?
The safety device of the electronic circuit board may have cut in because the safety devices have been activated. Turn the ignition key to the «STOP» position and check that all starting conditions are met.
What to do if my Stiga F 72 FL has uneven mowing and poor grass collection?
Uneven mowing and poor grass collection can occur if the cutting-means assembly is not parallel to the ground, the cutting means are inefficient, the forward speed is too high compared to the height of grass being cut, or the collector channel is blocked. Check the tire pressure, reduce the forward speed and/or raise the cutting-means assembly. If the grass is wet, wait for it to dry. Also, remove the grass catcher and empty the collector channel.
What to do if my Stiga F 72 FL Lawn Mower engine stops and the light goes off?
The safety device of the electronic circuit board may have cut in because of a flat battery, overvoltage caused by the charge regulator, or a badly connected battery. Turn the ignition key to the «STOP» position, recharge the battery, and check the battery connections.
Why does my Stiga F 72 FL Lawn Mower have unusual vibrations while working?
Unusual vibrations while working may occur if the cutting-means assembly is full of grass, the cutting means are unbalanced or loose, or the bolts and screws are loose. Clean the cutting means assembly and check and tighten all the engine and frame bolts.
Why is starting my Stiga Lawn Mower difficult or why does the engine run erratically?
Difficult starting or erratic engine running may be due to faulty carburetion. Clean or replace the air filter, flush out the float chamber, empty the fuel tank and refill with fresh fuel and check and replace the fuel filter if necessary.
Why does my Stiga Lawn Mower have weak engine performance during cutting?
Weak engine performance during cutting can be caused by the forward speed being too high in relation to the cutting height. Reduce the forward speed and/or raise the cutting height.
What to do if my Stiga Lawn Mower machine starts to vibrate abnormally?
If the machine starts to vibrate abnormally, it might have damaged or loose parts. Stop the machine and disconnect the spark plug cable. Inspect for damage and check for and tighten any loose parts.
Why does my Stiga F 72 FL Lawn Mower not move when the drive pedal is pressed?
If the machine does not move when the drive pedal is pressed, the release lever may be in position «B». Move it to position «A».
What to do if the light stays off with the key on in my Stiga F 72 FL?
If the light stays off with the key on, the safety device of the electronic circuit board may have cut in due to a badly connected battery, battery terminals crossed, badly earthed, flat battery, blown fuse, or wet circuit board. Turn the ignition key to the «STOP» position and check the connections, recharge the battery, replace the fuse (10 A), and dry using luke warm air.
What to do if the light flashes and the starter motor does not run when I turn the ignition key to «START» on my Stiga Lawn Mower?
The starting conditions have not been met. Check that all starting conditions are met.
General| Brand | Stiga |
|---|---|
| Model | F 72 FL |
| Category | Lawn Mower |
| Language | English |
Instructions and warnings for safe operation and operator training.
Essential checks and preparation steps before starting the machine.
Guidelines and precautions for safe operation of the machine.
Overview of the machine's components, intended use, and user types.
Details on the machine's identification plate and key parts.
Explanation of safety labels and essential precautions for machine use.
Procedure for safely removing the machine from its packaging.
Steps for assembling the machine and connecting the battery.
Instructions for installing the dashboard and steering wheel.
Procedure for attaching the control lever extension.
Instructions for assembling the machine's mobile cover.
Steps for installing the operator's seat onto the machine.
Procedure for assembling the grass collection system.
Instructions for attaching the side panels of the cutting deck.
Controls the direction of the machine's front wheels.
Regulates the engine's revolutions per minute (RPM).
Secures the machine in place when parked.
Controls the engine start, stop, and electrical systems.
Displays machine status, warnings, and system indicators.
Lever to engage and disengage the cutting blades.
Selects the desired height for grass cutting.
Pedal enabling reverse gear with cutting means engaged.
Controls for speed adjustment and engagement in hydrostatic drive.
Controls for speed adjustment and clutch in mechanical drive.
Crucial safety guidelines to follow during machine operation.
Explanation of the machine's safety systems and their function.
Essential checks and preparations before commencing operation.
Adjusting the operator's seat for optimal position and safety.
Ensuring correct tyre pressure for even cutting and performance.
Procedure for adding oil and fuel, including safety precautions.
Installing the grass catcher guard for safety.
Verifying all safety devices and operational systems are ready.
Step-by-step instructions for operating the machine.
Procedure for starting the engine.
Instructions for moving the machine without engaging the cutting unit.
Methods for safely stopping the machine.
Procedure for operating the machine in reverse gear.
Guidelines for effective and optimal grass cutting.
Safe procedure for emptying the grass collection system.
Troubleshooting steps for a blocked collection channel.
Procedures to follow after completing mowing tasks.
Final steps to shut down and secure the machine.
Instructions for cleaning the machine after use.
Proper procedures for storing the machine during extended periods.
Information on the electronic circuit board's protection mechanism.
Safety and operational guidelines for using the machine on slopes.
Tips for achieving an optimal lawn appearance through proper mowing.
Essential safety rules to follow during maintenance procedures.
Instructions on how to access the engine and mechanical parts.
Schedule and procedures for regular upkeep tasks.
Specific maintenance tasks for the engine.
Information regarding the maintenance of the rear axle.
Care, maintenance, and charging instructions for the battery.
Lubrication points and schedule for machine components.
Procedures for various adjustments and repairs on the machine.
Adjusting the cutting deck for optimal mowing performance.
Procedure for safely replacing the machine's wheels.
Guidelines for professional repair or replacement of tyres.
Procedure for replacing blown fuses.
Procedure for replacing the machine's light bulb.
Detailed instructions for working on the cutting system.
Diagnosing why the indicator light remains off when the key is on.
Troubleshooting issues with the starter motor not engaging.
Diagnosing why the starter motor fails to operate.
Troubleshooting engine start failures despite starter motor operation.
Addressing problems with difficult engine starting or uneven running.
Resolving issues of reduced engine power while mowing.
Diagnosing engine shutdown accompanied by a flashing warning lamp.
Troubleshooting engine shutdown and loss of electrical power.
Diagnosing engine shutdown while the indicator light remains active.
Addressing issues with cutting mechanism engagement or disengagement.
Resolving problems related to uneven cutting and inefficient grass collection.
Diagnosing and addressing excessive or abnormal vibrations.
Troubleshooting issues with the braking system's performance.
Addressing problems with erratic movement or loss of drive.
Diagnosing a complete failure of the drive system.
Identifying causes for severe and abnormal machine vibrations.
Information on the accessory for maintaining battery charge.
Information on the accessory for protecting the machine from dust.
