Stihl FS 361 C-M - User Manual

Other manuals for Stihl FS 361 C-M

Questions and Answers:

R
Ryan HicksAug 2, 2025
Why Stihl Trimmer engine does not start?
- F
  friedmanamandaAug 2, 2025
  Your Stihl Trimmer engine might not start due to several reasons. It could be that there is insufficient fuel in the fuel tank, in which case you should refuel. Another possibility is that the carburetor is too hot; if this is the case, cool down the trimmer and press the manual fuel pump bulb at least ten times before starting, even if the bulb is already filled with fuel. Also, the carburetor may be iced up, so allow the engine to warm up gradually to a temperature of about 50 °F (10 °C).
D
David SimsAug 7, 2025
Why does Stihl FS 361 C-M Trimmer engine stop while idling?
- J
  Joseph ParrishAug 7, 2025
  The engine might stop while idling because the carburetor is iced up. To resolve this, allow the engine to warm up gradually to a temperature of about 50 °F (10 °C).
C
Christina WagnerAug 10, 2025
Why my Stihl Trimmer engine does not start?
- M
  Mr. Anthony GrantAug 10, 2025
  If your Stihl Trimmer engine won't start, it could be due to a couple of reasons. First, check if there's enough fuel in the tank. If not, prepare a fuel mix and refuel the trimmer. Another potential cause is that the carburetor is too hot. In this case, allow the trimmer to cool down.
A
April ChoiAug 15, 2025
How to fix erratic idling of Stihl FS 361 C-M?
- D
  David MaloneAug 15, 2025
  If your Stihl Trimmer is idling erratically, it might be because the carburetor is iced up. Allow the engine to warm up gradually to a temperature of about 50 °F (10 °C) to resolve this issue.
R
Rachel BoydAug 19, 2025
What to do if my Stihl Trimmer engine stops while idling?
- M
  Michael MartinAug 20, 2025
  If your Stihl Trimmer engine stops while idling, the carburetor may have iced up. Allow the trimmer to warm up to +10°C.
K
Kathryn OwensAug 25, 2025
How to fix Stihl FS 361 C-M Trimmer if the engine does not reach maximum speed?
- C
  Christopher BakerAug 25, 2025
  If your Stihl Trimmer engine isn't reaching its maximum speed, it might not be correctly tuned to the ambient conditions. To resolve this, calibrate the brushcutter. Another possible cause is that the throttle cable isn't correctly adjusted; in that case, adjust the throttle cable.
K
Kristi MorganAug 27, 2025
Why does my Stihl FS 361 C-M engine idle erratically?
- A
  Amanda CookAug 28, 2025
  If the engine of your Stihl Trimmer idles erratically, it's possible that the carburetor has iced up. Allow the trimmer to warm up to +10°C.

Stihl FS 361 C-M Specifications

General

Fuel Tank Volume	0.75 l
Overall Length	1, 800 mm
Shaft Type	Straight
Displacement	36.3 cm³
Cutting Attachment	Grass cutting blade
Engine Type	2-MIX engine

Summary

Understanding the Manual

Guide to Using this Manual

Explains how to navigate the manual using signal words and symbols.

Signal Words

Defines signal words like DANGER, WARNING, and NOTICE for safety communication.

General Safety Precautions

Symbols in Text

Identifies the symbol used to refer to other chapters or sub-chapters.

Introduction to Safety

Emphasizes reading the manual and following safety precautions to prevent injury.

Product Overview and Safety

Main Parts Identification

Identifies and describes the main components of the trimmer and brushcutter.

Available Cutting Attachments

Lists and illustrates various cutting attachments and deflectors for use.

Product Safety Symbols

Explains safety symbols found on the trimmer/brushcutter itself.

Key Safety Instructions

Deflector for Mowing Heads Symbols

Describes safety symbols specific to deflectors used with mowing heads.

Deflector for Metal Cutting Attachments Symbols

Explains safety symbols for deflectors used with metal cutting attachments.

Introduction to Safety Instructions

Introduces the importance of safety precautions for operating the machine.

Intended Use

Specifies the approved uses and limitations of the trimmer/brushcutter.

Safe Operating Practices

Operator Requirements

Details physical and mental requirements for the operator and vibration effects.

Personal Protective Equipment (PPE)

Outlines necessary protective clothing, eye, and hearing protection.

Safe Trimmer;Brushcutter Operation

Covers safe handling of the cutting attachment and fire prevention.

Safe Fueling Procedures

Provides instructions and warnings for safe fueling of the machine.

Safe Operating Practices (Continued)

Preventing Fuel Spraying

Explains how to avoid fuel spraying or "geysering" during refueling.

Fuel Cap and Vapor Lock

Details safe fuel cap removal and troubleshooting vapor lock.

Before Operation Checks

Lists essential steps to perform before beginning any work.

Safe Engine Starting

Outlines the correct and safe procedure for starting the engine.

Safe Operating Practices (Continued)

Holding and Controlling the Unit

Guides on proper grip, stance, and control for safe operation.

Working Conditions and Safety

Advises on operating in suitable visibility, weather, and work areas.

Fire, Exhaust, and Dust Safety

Covers risks of fire from sparks and hazards of exhaust fumes.

General Operating Instructions

Covers emergency stops, idle settings, flywheel effect, and work area safety.

Safe Operating Practices (Continued)

Cutting Attachment Security and Hot Parts

Addresses secure attachment, damaged parts, and hot engine components.

Kickout (Blade Thrust) Safety

Explains kickout risk with metal attachments and how to mitigate it.

Using Mowing Heads Safely

Provides guidance on using mowing heads and line length.

Using Grass Cutting Blades

Details safe use of grass cutting blades and their types.

Safe Operating Practices (Continued)

Using Brush Knives Safely

Explains safe applications and techniques for brush knives.

Using Circular Saw Blades Safely

Covers safe techniques for cutting brush and small trees with saw blades.

Maintenance and Storage Safety

Maintenance and Repair Safety

Highlights safety during maintenance and repair operations.

Assembly and Adjustments

Before Starting Work Checklist

Lists essential steps to perform before beginning any work.

Assembling the Trimmer;Brushcutter

Introduces the assembly process for the main unit.

Mounting Handlebar and Control Handle

Step-by-step guide for attaching the handlebar and control handle.

Mounting;Removing Deflectors

Instructions for installing and removing deflectors.

Assembly and Adjustments (Continued)

Mounting;Removing Mowing Heads

Details the procedure for attaching and detaching mowing heads.

Mounting;Removing Metal Cutting Attachments

Guides on installing and removing metal cutting attachments.

Removing Metal Cutting Attachments

Steps for safely detaching metal cutting attachments.

Adjusting the Full Harness

Instructions for putting on and adjusting the operator's harness.

Assembly and Adjustments (Continued)

Adjusting the Handlebar

Describes how to adjust the handlebar for operator comfort and reach.

Balancing the Trimmer;Brushcutter

Explains how to achieve proper balance for effective operation.

Fueling and Engine Management

Mixing Fuel Requirements

Details the correct gasoline and oil mixture for the engine.

Mixing Fuel Procedures

Outlines the correct steps for mixing fuel and storing it safely.

Refueling the Trimmer;Brushcutter

Provides instructions for safely refueling the machine.

Starting and Stopping the Engine

Starting the Engine Safely

Guides on pre-start checks and the safe procedure for starting the engine.

Shutting Off the Engine

Explains the correct procedure for turning off the engine.

Operation Checks

Testing Controls

Details how to test the throttle trigger, lockout, and stop switch.

During Operation

General Trimmer;Brushcutter Operation

Covers safe operation, protective gear, and basic mowing techniques.

Adjusting the Nylon Line

Instructions for adjusting the nylon line on different mowing head types.

Engine Adjustment and Seasonal Settings

STIHL M-Tronic Engine Management

Explains the electronic engine management system.

Calibrating the Trimmer;Brushcutter

Guides on calibrating the unit for optimal performance.

Winter and Summer Operation Settings

Details adjustments for winter and summer operating conditions.

Post-Operation and Storage

Preparing for Transportation or Storage

Steps for safely preparing the unit for transport or long-term storage.

Cleaning and Maintenance

Cleaning the Trimmer;Brushcutter

Provides instructions for cleaning the power tool.

Inspection and Maintenance Schedule

Maintenance Chart Overview

Presents a chart outlining regular inspection and maintenance intervals.

Inspecting and Maintaining the Unit

Details specific checks for components like deflectors and air filters.

Sharpening and Balancing Cutting Attachments

Guides on sharpening and balancing metal cutting attachments.

Troubleshooting Guide

Trimmer;Brushcutter Troubleshooting

Lists common problems and their solutions for the trimmer/brushcutter.

Replacing the Air Filter

Step-by-step instructions for replacing the air filter.

Cleaning the Spark Plug

Guides on cleaning or replacing the spark plug.

Adjusting the Throttle Cable

Instructions for adjusting the throttle cable for proper function.

Technical Specifications

EPA and CARB Emission Information

Details emission compliance periods and standards.

STIHL FS 361 C-M, 461 C-M Specifications

Lists technical data including displacement, power, and speed.

Power Tool and Deflector Symbols

Explains various symbols found on the power tool and its deflector.

Engineering Improvements

Discusses STIHL's commitment to product improvement.

Approved Combinations and Parts

Approved Deflector, Attachment, and Harness Combinations

Lists approved combinations for safe and effective use.

Replacement Parts and Disposal

Genuine STIHL Replacement Parts

Recommends using genuine STIHL parts for safety and performance.

Power Tool Disposal Procedures

Outlines environmentally friendly disposal methods for the power tool.

Warranty Information

STIHL Limited Warranty Policy

Details the terms and conditions of the STIHL limited warranty.

Federal Emission Control Warranty

Explains the warranty for the engine's emission control system.

Federal Emission Control Warranty Statement

Continues the explanation of the federal emission control system warranty.

California Emissions Control Warranty

Outlines the emissions control system warranty specific to California.

Trademarks and Legal Information

Registered Trademarks

Lists STIHL's registered trademarks.

Common Law Trademarks

Lists STIHL's common law trademarks.

STIHL Incorporated Contact Information

Provides the address for STIHL Incorporated.

Related product manuals

Stihl FS 361 C-M - User Manual

Table of Contents

Other manuals for Stihl FS 361 C-M

Questions and Answers:

Stihl FS 361 C-M Specifications

Summary

Understanding the Manual

Guide to Using this Manual

Signal Words

General Safety Precautions

Symbols in Text

Introduction to Safety

Product Overview and Safety

Main Parts Identification

Available Cutting Attachments

Product Safety Symbols

Key Safety Instructions

Deflector for Mowing Heads Symbols

Deflector for Metal Cutting Attachments Symbols

Introduction to Safety Instructions

Intended Use

Safe Operating Practices

Operator Requirements

Personal Protective Equipment (PPE)

Safe Trimmer;Brushcutter Operation

Safe Fueling Procedures

Safe Operating Practices (Continued)

Preventing Fuel Spraying

Fuel Cap and Vapor Lock

Before Operation Checks

Safe Engine Starting

Safe Operating Practices (Continued)

Holding and Controlling the Unit

Working Conditions and Safety

Fire, Exhaust, and Dust Safety

General Operating Instructions

Safe Operating Practices (Continued)

Cutting Attachment Security and Hot Parts

Kickout (Blade Thrust) Safety

Using Mowing Heads Safely

Using Grass Cutting Blades

Safe Operating Practices (Continued)

Using Brush Knives Safely

Using Circular Saw Blades Safely

Maintenance and Storage Safety

Maintenance and Repair Safety

Assembly and Adjustments

Before Starting Work Checklist

Assembling the Trimmer;Brushcutter

Mounting Handlebar and Control Handle

Mounting;Removing Deflectors

Assembly and Adjustments (Continued)

Mounting;Removing Mowing Heads

Mounting;Removing Metal Cutting Attachments

Removing Metal Cutting Attachments

Adjusting the Full Harness

Assembly and Adjustments (Continued)

Adjusting the Handlebar

Balancing the Trimmer;Brushcutter

Fueling and Engine Management

Mixing Fuel Requirements

Mixing Fuel Procedures

Refueling the Trimmer;Brushcutter

Starting and Stopping the Engine

Starting the Engine Safely

Shutting Off the Engine

Operation Checks

Testing Controls

During Operation

General Trimmer;Brushcutter Operation

Adjusting the Nylon Line

Engine Adjustment and Seasonal Settings

STIHL M-Tronic Engine Management

Calibrating the Trimmer;Brushcutter

Winter and Summer Operation Settings

Post-Operation and Storage

Preparing for Transportation or Storage

Cleaning and Maintenance

Cleaning the Trimmer;Brushcutter

Inspection and Maintenance Schedule