Strong SRT7807 User Manual

3.1.1 Connection of multiple xed antennas via DiSEqC 1.0
Fig. d
A) Connect the LNBs of your fixed antenna to the inputs of a DiSEqC 1.0 switch using a good
quality coaxial cable and suitable ‘F-connectors'.
B) Connect the output or “to receiver” of the DiSEqC 1.0 switch to the SAT IN connector on your
receiver. Use good quality coaxial cable and suitable “F-connectors”.
C) Plug the power adapter jack to the receiver and the other end to a suitable wall outlet.
3.2 Connecting to a digital audio amplier
Fig. d
Connect one end of a good quality coaxial audio cable to the S/PDIF output of your receiver and the
other end to the coaxial audio input of your home theatre, amplifier or any other device supporting
digital audio.
3.3 Basic connection using an HDMI cable
Fig. d
A) Connect the LNB of your satellite antenna to the SAT IN connector of your receiver using a
good quality coaxial cable and suitable ‘F-connector' plugs.
B) Connect one end of a good quality HDMI cable to the HDMI output on your receiver and the
other end to the HDMI input of your TV.
C) Plug the power adapter to a suitable wall outlet.
3.4 Basic connection using a SCART cable
Fig. d
A) Connect the LNB of your satellite antenna to the SAT IN connector of your receiver using a
good quality coax cable and suitable ‘F-connector' plugs.
B) Connect one end of a good quality Scart cable to the TV SCART connector on your receiver
and the other end to the SCART input of your TV.
C) Plug the power adapter to a suitable wall outlet.
3.5 Connecting to the Internet
The receiver connects to the Internet through the Internet router or DSL/cable modem in your home
network. It connects to the home network over its Ethernet port or Wi-Fi.
Fig. d
Connect one end of the Ethernet cable to the receiver and the other end to the LAN port at the router or
DSL/cable modem.
3.6 Connection to main power supply
Fig. d
After all the connections are done you can connect your receiver to power using the supplied external
AC/DC adapter. Now plug the adapter into the wall socket.
4.0 STARTING UP FOR THE FIRST TIME
Once you properly installed and connected all cables of the receiver, setup your receiver step by step by
following the installation wizard.
It will guide you through the basic installation and channel searching process.
7

Strong SRT7807 Specifications

Demodulator

demodulation	QPSK, 8PSK
input symbol rate	1 ~ 45 Ms/s
FEC decoder DVB-S2 QPSK mode	1/2, 2/3, 3/4, 5/6, 7/8
FEC decoder DVB-S2 8PSK mode	1/2, 3/5, 2/3, 3/4, 4/5, 5/6, 8/9, 9/10

Video

video standard	MPEG-2, MP@ML, MP@HL, MPEG-4, AVC/H.264 MP@L4.2, HP@L4.2
max video resolution	1080p
aspect ratio	4:3 and 16:9
video resolution HDMI	576i/576p, 720p, 1080i, 1080p
video resolution SCART	PAL

Audio

audio standard	MPEG-1, MPEG-2 layer I&II

Tuner

tuner type	F Type, IEC169-24, Female 75ohm
input frequency range	950 – 2150 MHz
signal level	-60 to -25 dBm
LNB power	13/18 V DC (+/- 1 V)
DiSEqC version	1.0/1.1/1.2

System Memory

CPU	M3528 2000DMIPS
flash memory	28 MB NAND Flash
system memory	256MB DDR3

Connectors

SAT IN	present
S/PDIF (coaxial)	present
smartcard reader	1x, on right side panel
HDMI 1.4b	present
TV SCART	CVBS only
Ethernet (RJ45)	present
IR (infrared)	1x38KHz IR, NEC Protocol
power adapter	12 V/1.5 A
USB 2.0 port Type A	1x, 5 V/500 mA (max.) supported (with duster cover)

General Data

supply voltage	AC 100 - 240 V 50/60 Hz
input voltage	DC 12 V, 1.5 A
size (W x D x H)	168 x 99 x 39 mm
net weight	0.5 kg