Why is my Subaru Adaptive Cruise Control activated when there is no vehicle in front?
A vehicle in the neighboring lane might be detected as being directly in front of you, depending on the road conditions. If you are driving on or near a curve, braking control may be activated in response to guardrails, the angle of the steering wheel, or roadside structures.
Why is my Subaru Adaptive Cruise Control braking frequently in heavy traffic?
When Adaptive Cruise Control is activated, the EyeSight system controls the car based on the movement of vehicles or objects in front. As a result, acceleration and deceleration may be more frequent while the system adjusts to vehicles or objects the camera system is detecting. If maintaining a consistent following distance is difficult under certain conditions (such as in heavy traffic, poor weather, or urban environments), it is advised not to use Adaptive Cruise Control.
Why is not displayed on my Subaru EyeSight Automobile Accessories?
The symbol in your Subaru Automobile Accessories will not be displayed if the requirements for setting cruise control are not met. These requirements include: the brake pedal is depressed, the vehicle speed is over 90 MPH (145 km/h), the combination meter indicates a position other than D (select lever or paddle shift switches are manually operated), the driver’s seatbelt is unfastened, any door is opened (except the rear gate/trunk), the vehicle is on a steep grade, the steering wheel is turned significantly, or the parking brake is released.
Why does braking control activate frequently in heavy traffic with my Subaru EyeSight?
Unlike a human driver, the EyeSight system in your Subaru Automobile Accessories controls acceleration and deceleration based solely on the actions of vehicles or objects in front. This can lead to more frequent adjustments as the system reacts to detected vehicles or objects. If maintaining a consistent following distance is difficult under certain conditions, such as bad weather or urban environments, consider deactivating Adaptive Cruise Control.
Why is acceleration slower or faster when the vehicle in front turns or distance increases in my Subaru Automobile Accessories?
If acceleration feels slower or faster when the vehicle in front turns off or the distance increases in your Subaru Automobile Accessories, EyeSight’s reaction time might be affected. Depending on when the detection of the vehicle in front is lost, EyeSight's response may be slower, causing acceleration to feel delayed and braking time to feel longer than normal.
Why does braking control activate frequently with Adaptive Cruise Control in heavy traffic for Subaru EyeSight?
When Adaptive Cruise Control is activated, the EyeSight system controls the vehicle based on the movement of vehicles or objects in front. This can lead to more frequent acceleration and deceleration as the system adjusts. If maintaining a consistent following distance is difficult in heavy traffic, poor weather, or urban environments, consider deactivating Adaptive Cruise Control.
Why is a vehicle not detected, detected late, or detection lost quickly by my Subaru EyeSight?
If, in your Subaru Automobile Accessories, a vehicle in front isn't detected, is detected later, or detection is quickly lost, consider these possibilities: Detection of stopped vehicles or those moving very slowly might be difficult. Also, a dirty or fogged windshield can impede detection, so clean it. The vehicle in front might be too far away, as EyeSight's maximum detection distance is approximately 360 ft (110 m). Additionally, detection range is limited on curves, roads with repeated uphill and downhill grades, or banked roads. Detection may be delayed after the vehicle in front changes, or if water or snow is kicked up by the vehicle in front.
Why does the Lead Vehicle Start Alert activate with no vehicle in front in my Subaru EyeSight?
If the Lead Vehicle Start Alert activates in your Subaru Automobile Accessories even when there's no vehicle in front, it might be responding to other objects appearing in front of your vehicle due to surrounding objects, traffic environment, or weather conditions.
Why does the 'brake more' warning timing vary in my Subaru EyeSight Automobile Accessories?
The “brake more” warning in your Subaru Automobile Accessories activates when the system determines that more braking is necessary, based on factors like the distance from the vehicle in front and the speed difference. The timing of the warning can vary depending on how the brakes are applied relative to the vehicle in front and your speed relative to that vehicle.
Why does my Subaru EyeSight Automobile Accessories make a noise when automatic braking activates?
The automatic braking control in your Subaru Automobile Accessories has mechanical components that may produce audible sounds during operation. This sound does not necessarily indicate a malfunction.
General| Type | Driver Assist Technology |
|---|---|
| Camera System | Stereo Camera |
| Additional Functions | Adaptive Cruise Control, Lane Keep Assist |
| Detection Range | Up to 110 meters |
| System Activation | Automatic upon vehicle start |
| Availability | Standard or Optional on most Subaru models |
To Next Page
