Why is there no heat in my Sundance Spas Hot Tub?
If your Sundance Spas Hot Tub isn't heating, start by checking the thermostat setting. Ensure the hot tub cover is in place while heating. Also, verify the settings to see if your hot tub is in economy mode.
How to reduce the water temperature in my Sundance Spas Hot Tub?
If the water in your Sundance Spas Hot Tub is too hot, reduce the thermostat setting.
What to do if Sundance Spas Hot Tub has no heat?
If your Sundance Spas hot tub isn't heating, check the thermostat setting and ensure the spa cover is in place while heating. Also, verify if your spa is in economy filtration/heating mode.
What to do if Sundance Spas Hot Tub pump doesn't operate but light does?
If the pump in your Sundance Spas hot tub isn't working but the light is, it could be due to insufficient power or low water level. Press the JETS 1 button. If there's no water movement, ensure the spa is getting power and check the water level. Alternatively, the pump may need priming. Press the JETS 1 button several times for 5-10 seconds each time. Turn the power off and release air by loosening the cap on the massage selector or removing the filter. Remember to tighten the cap or reinstall the filter before restarting the pump.
How to fix a pump that does not operate on my Sundance Spas Dover?
If the pump on your Sundance Spas Hot Tub isn't working, first press the JETS 1 button. Ensure power is going to the hot tub and verify the water level. Also, check that all jets are in the open position. The pump may need priming, especially after draining and refilling. Press the JETS 1 button several times for 5-10 seconds each time. Finally, turn the power off and release air from the plumbing by removing the filter cartridge. Reinstall the filter before turning the power back on.
How to improve poor jet action in my Sundance Spas Hot Tub?
To improve poor jet action in your Sundance Spas Hot Tub, ensure all jets are fully open. Press the JETS 1 button to activate pump #1. Confirm all air controls are in the 'on' position. Also, check the filter for dirt and clean it if necessary.
What to do if none of the components operate on my Sundance Spas Dover?
If none of the components are working on your Sundance Spas Hot Tub, check if there is power to the hot tub and see if the household circuit breaker has tripped.
What to do if my Sundance Spas Hot Tub displays FL--1 or FL--2 error?
If you see 'FL--1' or 'FL--2' on your Sundance Spas Hot Tub display, immediately turn the power off. Verify the water level is above all jets but below the lowest pillow; add water if needed. Check for a clogged or dirty filter cartridge. To purge an air lock, remove the filter cartridge and use a garden hose over the filter cartridge wall fitting with a rag seal while a helper turns on the water for 30 seconds, then off. Reinstall the filter cartridge and check the hot tub. If the circulation pump isn't running, turn the power off at the main breaker, then back on.
Why is my Sundance Spas Dover water too hot?
If your Sundance Spas hot tub water is too hot, reduce the thermostat setting to ensure the heater turns off.
What to do if none of the components operate in my Sundance Spas Hot Tub?
If none of the components (like the pump or light) are working in your Sundance Spas hot tub, check if there is power to the spa and if the household circuit breaker has tripped.
Outlines FCC compliance and measures for potential interference with radio communications.
Factors to consider when choosing an ideal outdoor location for your spa.
Configures the primary filtration cycle, including start time and duration.
Detailed instructions for cleaning and replacing the spa's MicroClean filter cartridges.
How the spa enters "summer logic" to prevent overheating in high ambient temperatures.
Indicates a cool condition where circulation and heater activate to reach set temperature.
Alerts to a potential freeze condition, activating pumps and heater to prevent damage.
Signals a malfunctioning or shorted temperature sensor, disabling the heater.
Steps to correct FL--1 and FL--2 flow errors, including checking water level and filter.
Troubleshooting steps for when no spa components are functioning.
Diagnosing issues when the pump is not operating or water is not flowing.
General| Brand | Sundance Spas |
|---|---|
| Model | Dover |
| Category | Hot Tub |
| Language | English |
To Next Page