Need help?Do you have a question about the Sunlux XL-3200 and is the answer not in the manual?
Provides instructions on using the XL-3200 scanner and navigating the manual.
Details the scanner's area-imaging technology for fast and accurate barcode reading.
Explains the methods for setting up and customizing the scanner's functions.
Describes how to configure the scanner by scanning special programming barcodes.
Details how to configure the scanner using serial commands sent from a host device.
Explains the serial command used to read the contents of contiguous registers in the scanner engine.
Details the serial command used to write data into contiguous registers within the scanner engine.
Describes the command to save current scanner register data into external EEPROM for persistence.
Illustrates how programming barcodes correlate to their equivalent serial commands for configuration.
Provides information on restoring the scanner to its original factory default settings.
Explains the serial communication interface and its default parameters for connecting to host devices.
Details how to set the data transmission speed for serial communication to match host requirements.
Describes the scanner's USB connectivity options and how to configure them.
Covers USB DATAPIPE, HID-KBW, COM Port Emulation, and HID-POS communication modes.
Allows selection of different keyboard layouts for international compatibility via USB.
Configures beep on unknown characters, inter-key delays, Caps Lock, case conversion, and numeric keypad emulation.
Details program access, scanned data acquisition format, and VID/PID identification.
Describes the default scan mode where a trigger pull activates a decode session.
Details the scan mode where the scanner automatically activates decode sessions continuously.
Sets the maximum duration for a single decode session before it automatically ends.
Configures the time delay between consecutive successful barcode decode sessions.
Describes the scan mode that waits for ambient illumination changes to activate decode sessions.
Sets the time the engine waits for image stabilization before activating a decode session.
Adjusts the scanner's responsiveness to changes in ambient illumination for triggering scans.
Explains the scan mode activated by a host command, rather than a manual trigger pull.
Details the infrared trigger scan mode, activated by holding the trigger for an extended period.
Describes the settings for the illumination LED, including Normal, Always ON, and OFF states.
Explains the aiming beam settings, including Normal, Always ON, and OFF states for target positioning.
Enables or disables all notification beeps from the scanner, allowing silent operation.
Configures the audible beep that signals a successful barcode read.
Sets the frequency (pitch) of the good read beep indicator.
Adjusts the length of time the good read beep sound is emitted.
Controls the illumination of the LED indicator for a successful barcode read.
Configures additional notifications ('F' for no read, 'S' for good read) appended to barcode data.
Enables or disables the addition of AIM symbology identifiers to the scanned data.
Enables or disables the inclusion of Code ID identifiers in the scanned data output.
Configures carriage return, line feed, or tab characters to mark the end of scanned data.
Provides general controls for enabling or disabling all barcode symbologies.
Lists and describes configuration options for various 1D barcode types.
Configuration settings for the Code 128 barcode symbology.
Configuration settings for the EAN-8 barcode symbology.
Configuration settings for the EAN-13 barcode symbology.
Configuration settings for the UPC-E barcode symbology.
Configuration settings for the UPC-A barcode symbology.
Configuration settings for the Interleaved 2 of 5 barcode symbology.
Configuration settings for the Code 39 barcode symbology.
Lists and describes configuration options for various 2D barcode types.
Configuration settings for the PDF417 barcode symbology.
Configuration settings for the Data Matrix barcode symbology.
Configuration settings for the QR Code barcode symbology.
A table listing all scanner parameters and their factory default settings.
A reference table mapping barcode symbologies to their AIM Identifiers.
A table mapping barcode symbologies to their original and visible Code IDs.
Provides step-by-step examples for programming scanner parameters using barcodes.
Lists common serial commands for configuring and querying the scanner's settings.
General| Brand | Sunlux |
|---|---|
| Model | XL-3200 |
| Category | Barcode Reader |
| Language | English |
To Next Page
