Need help?Do you have a question about the SunTech ST4310 and is the answer not in the manual?
General| Operating Temperature | -20°C to +60°C |
|---|---|
| GSM Frequency | 850/900/1800/1900 MHz |
| Internal Memory | 4MB |
| Accelerometer | Yes |
| Baud Rate | 9600 bps |
| TTFF (Cold Start) | 35 s |
| TTFF (Hot Start) | 1 s |
Details the three operation modes: driving, parking, and emergency.
Describes AVL report types, storage limits, and priority of reports.
Explains how to change device parameters using LTE-M1 or SMS.
Device supports Sleep and Deep Sleep for power saving when parked.
LEDs indicate LTE-M1 and GPS states for error checking.
Details the device's 2 output, 3 input, and ignition lines.
Enables remote firmware updates via LTE-M1, simplifying maintenance.
Monitors unauthorized movement while parked and sends emergency reports.
Detects and reports vehicle over-speed conditions to the server.
Alerts if the GPS antenna is disconnected, applicable for external antennas.
Monitors main power line status and alerts on disconnection or voltage drops.
Alerts for battery errors related to charging, applicable to battery models.
Defines the structure for commands sent from the server to the device.
Defines the structure for reports sent from the device to the server.
Configures network parameters and PIN for LTE-M1 connectivity.
Sets whether Output 1 is open or GND when active.
Sets the number of pulses for Output 1.
Sets the duration for which Pulse 1 remains active.
Sets the duration for which Pulse 1 remains inactive.
Configures the baud rate for serial communication (RS232).
Sets up to four phone numbers for sending SMS commands to the device.
Locks incoming calls to authorized phone numbers.
Sets up to five phone numbers for incoming calls to the device.
Sets phone numbers for outgoing calls initiated by the device.
Enables/disables parking lock and sets its operational parameters.
Sets the speed limit for triggering over-speed alerts.
Configures power saving modes: disabled, deep sleep, or enabled sleep.
Sets the connection type with the server (KEEP_CON, KEEP_DISCON, KEEP_NOP).
Enables or disables data compression for transmission.
Enables sending multiple reports in one packet for faster transmission.
Enables or disables the check for main power disconnection.
Enables or disables the check for backup battery errors.
Configures motion sensor parameters: motion, collision, and shock detection levels.
Enables or disables the support for call functionality with a headset.
Enables or disables the geo-fence feature for location-based alerts.
Configures data logging via RS232, with options for 'No Use' or 'Enable'.
Sets the protocol type for backup server communication (TCP or UDP).
Configures server acknowledgement for UDP data transmission.
Specifies the device port for receiving commands via UDP.
Voltage threshold to stop charging the backup battery in 12V vehicles.
Voltage level used to check the status of the vehicle's 12V battery.
Voltage threshold to protect the vehicle battery by stopping device operation.
Threshold for virtual ignition to detect driving state based on power.
Threshold for virtual ignition to detect parking state based on power.
Sets the delay before entering shock detection mode after ignition off.
Sets the sensitivity level for detecting motion violations.
Sets the sensitivity level for detecting shock violations.
Sets the gravity threshold for reporting collisions.
Threshold for virtual ignition when ignition is on.
Delay time for virtual ignition when ignition is on.
Percentage setting for virtual ignition when ignition is on.
Threshold for virtual ignition when ignition is off.
Delay time for virtual ignition when ignition is off.
Percentage setting for virtual ignition when ignition is off.
Resets all device parameters to factory defaults and reboots the unit.
Retrieves parameter settings and current device status.
Activates Output 1 to its defined status.
Requests the unique SIM card identifier (IMSI).
Requests and displays the device's model, protocol, and software version.
Erases all buffered data and disables outputs for device initialization.
Resets the message sequence number to zero.
Reboots the device unit to restart its operations.
Step-by-step instructions for inserting the SIM card.
Guidance on using the backup battery when main power is unavailable.
Details on how the device should be fixed to the vehicle.
Illustrates the correct assembly procedure for the device.
Interprets blue LED blink counts to diagnose LTE-M1 connection and errors.
Cautions on USB connection, vehicle mounting, and backup battery usage.
To Next Page
