How to fix Sunwave Tech. SRC-3000 when LCD does not show anything?
If the LCD on your Sunwave Tech. Remote Control doesn't display anything when touched, the batteries may be dead. Replace them with three new AAA alkaline batteries, and ensure they are installed correctly.
What to do if Sunwave Tech. Remote Control SRC-3000 doesn’t operate a device?
If your Sunwave Tech. SRC-3000 Remote Control isn't operating a device, ensure the desired device key on the LCD panel is selected. Try moving closer to the device, as the maximum operating distance is approximately 30 feet. Also, make sure you're aiming the remote directly at the device without any obstructions. Verify that programming, either through the learning function or manufacturer codes, was done correctly and re-teach the key.
Why is IR learning not successful on Sunwave Tech. Remote Control?
If IR learning isn't successful on your Sunwave Tech. Remote Control, replace the batteries in both the remote and the device remote you are trying to configure. Keep the distance between the two remotes about 2~4 inches. Avoid using the learn function near an incandescent lamp. Note that the memory capacity is 56 keys for each of eight models. If you still can’t control your AV devices after successful learning, repeat the learning procedure again. If the problem persists, the original remote might not be compatible with the learning procedure.
What to do if Sunwave Tech. Remote Control cannot operate a device after learning function?
If you cannot operate a device with your Sunwave Tech. Remote Control even after using the learning function, ensure that the remote has correctly learned the target device’s remote control code. You may need to delete the device data from the remote and repeat the learning function. Also, verify that you haven't programmed more than one remote for a given device.
Why does Sunwave Tech. SRC-3000 Remote Control show “ERROR” during the learning procedure?
If you see an “ERROR” message on the LCD of your Sunwave Tech. Remote Control during the learning procedure, ensure you hold the target remote’s key until the screen displays 'Ok' or 'Error'. Keep the two remotes about 2~4 inches (5~10 cm) apart, and ensure your device remote control is aiming directly at the learning eye of the remote.
How to troubleshoot Sunwave Tech. SRC-3000 Remote Control when macro does not work?
If the macro function on your Sunwave Tech. Remote Control isn't working, make sure to aim the remote at the devices while the macro commands are being sent. Also, verify that the macro was properly set up.
What does “ERROR” mean on Sunwave Tech. SRC-3000 during operation?
If you see an “ERROR” message displayed during operation of your Sunwave Tech. Remote Control, the key you pressed likely hasn't been taught. Teach the key using the learning procedure.
What if a key of my existing remote performs two or more functions with Sunwave Tech. SRC-3000 Remote Control?
If a key on your existing remote performs multiple functions, teach different keys of your Sunwave Tech. Remote Control for each of those different commands, as each key can only learn one command.
Why won't my VCR record with Sunwave Tech. SRC-3000?
If your VCR won't record when using the Sunwave Tech. Remote Control, press the REC key for two seconds; this is a safety feature.
Why does the LCD screen turn off on Sunwave Tech. SRC-3000 Remote Control?
The LCD screen on your Sunwave Tech. Remote Control is preset to automatically switch off after a Power Down time of 90 seconds. Simply tap the touch screen to turn it back on.
Provides information on using the SRC-3000 Touch Screen Remote Control and manual accuracy.
Highlights the main features of the SRC-3000, including its touch screen, macro function, and device control capabilities.
Instructions for checking the contents of the SRC-3000 package to ensure all items are included and undamaged.
Identifies and explains the purpose of each physical component of the SRC-3000 remote control.
Step-by-step guide on how to properly insert AAA alkaline batteries into the SRC-3000 remote control.
Explains the battery low icon on the SRC-3000's LCD screen and what it signifies about battery power.
Provides essential advice and safety precautions for using and handling batteries with the SRC-3000 remote.
Details the dynamic nature of the SRC-3000's touch screen and its soft key functionality.
Instructions on how to turn on the SRC-3000 by touching the screen and information about its automatic power-off feature.
Important guidelines for safely operating, cleaning, and preventing damage to the SRC-3000's touch screen.
Explains how to utilize the touch screen's soft keys for programming, macros, and device control.
Procedure for entering the SRC-3000's setup mode to configure various settings and options.
Illustrates and describes the primary function keys available on the SRC-3000 remote control interface.
Guide to personalizing the SRC-3000's touch screen display to match your existing remote controls.
Details on using the 'Code' option for pre-programmed setup and the 'Learn' option for copying codes from other remotes.
Step-by-step instructions for manually and automatically programming devices using the SRC-3000's code library.
Comprehensive guide on teaching the SRC-3000 infrared signals directly from a device's original remote control.
Instructions on how to delete specific key codes or all device codes from the SRC-3000.
Explains the process of creating macros, sequences of commands triggered by a single key press, including time delays.
Procedure to restore the SRC-3000 to its original factory settings, including erasing all custom macros and codes.
Guide on transferring settings and data between two SRC-3000 remotes using an optional connection cable.
Instructions for configuring the backlight's ON time and adjusting its sensitivity based on ambient light.
Details on how to fine-tune the light sensor's response for automatic backlight activation.
Instructions on how to enable or disable the audible beep sound associated with key presses on the SRC-3000.
Explains how to navigate between different pages of device controls displayed on the SRC-3000's touch screen.
Guide on how to check which keys have been programmed with macro sequences for a selected device.
How to stop an active macro sequence prematurely by pressing a specific key combination.
Fundamental steps required to operate electronic devices using the SRC-3000 after successful setup.
A comprehensive list of all the operational functions and capabilities offered by the SRC-3000 remote control.
Provides detailed technical data for the SRC-3000, including dimensions, memory, power consumption, and operating range.
Details the optional SLC-2080 USB cable for transmitting data and settings between SRC-3000 units.
Steps to resolve issues when the SRC-3000's LCD screen does not display anything when touched.
Solutions for when the SRC-3000 fails to control a connected electronic device as expected.
Addresses problems encountered during the learning function, including errors or device non-operation after learning.
Guidance on resolving 'ERROR' messages that appear on the screen during remote operation or setup.
Explanation for why a VCR may not record, related to the specific safety feature of the REC key.
Steps to fix issues when the infrared learning process fails, checking batteries, distance, and environment.
Tips for resolving problems where macros are not executing correctly or not working at all.
Solutions for issues where a learned key on the SRC-3000 performs multiple functions incorrectly.
Information about the SRC-3000's automatic LCD screen turn-off feature and how to reactivate it.
General| Brand | Sunwave Tech. |
|---|---|
| Model | SRC-3000 |
| Category | Remote Control |
| Language | English |
To Next Page
