Sunwave Tech. SRC-3310/9320

Questions and Answers

J
Jacqueline WalkerAug 17, 2025
Why does the LCD screen turn off on my Sunwave Tech. SRC-3310/9320 Remote Control?
- M
  medinamatthewAug 17, 2025
  If the LCD screen turns off on your Sunwave Tech. Remote Control, simply tap the LCD screen or any button to turn it back on. The remote is preset to automatically switch the LCD off after a certain period. You can also reset the Power Down time.
J
Jason GarrettAug 20, 2025
What to do if my Sunwave Tech. Remote Control isn't operating a device?
- C
  Christopher MoranAug 20, 2025
  If your Sunwave Tech. Remote Control isn't operating a device, ensure the correct device screen is selected on the LCD panel. Move closer to the device, staying within approximately 30 feet, and aim the remote directly at it, removing any obstructions. Also, verify that programming via the learning function or manufacturer codes was done correctly, and try re-teaching the button.
M
Marcus WilkersonAug 23, 2025
How to fix a Sunwave Tech. SRC-3310/9320 Remote Control when the macro doesn't work?
- T
  Tiffany HernandezAug 23, 2025
  If the macro function on your Sunwave Tech. Remote Control isn't working, it might not have been set up correctly. Ensure you're aiming the remote at the devices while the macro commands are being sent. You may need to repeat the macro set-up procedure.
M
Miranda ThomasAug 26, 2025
What does 'ERROR' display during operation mean on my Sunwave Tech. SRC-3310/9320 Remote Control?
- F
  frazierbrendaAug 26, 2025
  If you see 'ERROR' on the LCD during operation of your Sunwave Tech. Remote Control, it means the button you pressed hasn't been taught. Use the learning procedure to teach the button.
J
john80Aug 28, 2025
What to do if Sunwave Tech. Remote Control cannot operate a device after teaching?
- T
  Tim ChangAug 28, 2025
  If you cannot operate a device even after teaching it using the learning function on your Sunwave Tech. Remote Control, ensure you correctly 'taught' your device's remote control to the device. Try deleting the device data and repeating the learning function. Also, make sure you didn't program more than one remote for the same device.
G
George ShieldsAug 31, 2025
How to solve problems changing channels on Sunwave Tech. SRC-3310/9320 Remote Control?
- J
  Jeffrey SimmonsAug 31, 2025
  If you are experiencing problems changing channels with your Sunwave Tech. Remote Control, and your original remote required pressing the ENTER key after selecting a channel, make sure to press the ENTER key on the Sunwave Tech. remote as well.
A
Amber WeissSep 2, 2025
Why won't my VCR record with the Sunwave Tech. SRC-3310/9320 Remote Control?
- B
  brenda39Sep 3, 2025
  If your VCR will not record when using the Sunwave Tech. Remote Control, press and hold the REC key for 2 seconds. This is a safety feature.
D
Daniel DuranSep 5, 2025
How to fix a Sunwave Tech. SRC-3310/9320 Remote Control with a blank LCD screen?
- B
  Brad DavisSep 5, 2025
  If the LCD on your Sunwave Tech. Remote Control doesn't show anything when touched or when pressing the rubber buttons, the batteries may be dead. Replace them with four new AA alkaline batteries and ensure they are properly installed.
A
Ana SmithSep 8, 2025
What does 'ERROR' during learning mean on my Sunwave Tech. SRC-3310/9320?
- M
  mariajacobsonSep 8, 2025
  If you see 'ERROR' displayed on the LCD during the learning procedure on your Sunwave Tech. Remote Control, ensure you hold the other remote's button down for about 2 seconds. Also, verify that you haven't programmed more than one remote for a given device. Keep the two remotes 2-4 inches apart, aiming directly at each other.
M
Melissa JuarezSep 12, 2025
What if a button performs multiple functions on Sunwave Tech. SRC-3310/9320?
- A
  Amy BrooksSep 12, 2025
  If a button on your existing remote performs multiple functions, teach different buttons on the Sunwave Tech. Remote Control for each of those different commands, as each button can only learn one command.