Need help?Do you have a question about the Swegon SILVER Series and is the answer not in the manual?
General| Brand | Swegon |
|---|---|
| Model | SILVER Series |
| Category | Air Handlers |
| Language | English |
Defines the proper use of the air handling unit for ventilation and air handling purposes.
Outlines potential mechanical, electrical, and thermal hazards associated with the equipment.
Details regulations, proper use, and need for immediate rectification of faults for safe operation.
Provides specific safety advice for operating components like heat exchangers and electrical connections.
Covers requirements for cleaning, protecting, and storing unit components to prevent damage.
Details inspection upon delivery, securing loose parts, and safe transport of equipment components.
Specifies requirements for stable, level foundations and base frames for equipment positioning.
Addresses ensuring accessibility, alignment, and protection of equipment during installation.
Guides on insulating the equipment from structure-borne noise and vibration using appropriate base supports.
Mandates bridging non-conducting points and grounding the entire assembly for electrical safety.
Details the correct installation and care of frost protection capillary tubing for heat exchangers.
Explains how to connect equipment components using provided materials and securing methods.
Describes methods and accessories for safely installing and removing fan units.
Specifies requirements for motor overload protection, including type and settings, to prevent damage.
Outlines essential safety precautions and procedures for making electrical connections by authorized personnel.
Provides wiring diagrams and instructions for connecting three-phase motors for single-speed operation.
Details wiring and phase-winding for two-speed motors using Dahlander coupling.
Explains wiring configurations for two-speed motors with separate stator windings.
Presents wiring diagrams for three-speed motors, including Dahlander coupling variants.
Illustrates typical wiring diagrams and provides essential considerations for using frequency converters.
Instructs on securing pocket type filters, ensuring an airtight seal, and proper maintenance.
Covers connection requirements, operation, and protection of water coils for heating and cooling.
Details the installation and handling of droplet separator cartridges and their orientation.
Emphasizes ensuring safe condensate drainage for steam heaters during operation.
Provides guidelines for refrigerant lines, including pressure, temperature limits, and purging.
Advises on tension-free air duct connections and proper grounding for system integration.
Explains the importance and installation of siphons for fault-free water drainage and preventing odour.
Covers regulations and guidelines for installing gas surface burners and connections.
Details secure installation, flame tube adaptation, and temperature limiter placement for direct lighted burners.
Guides on pre-commissioning checks, safety measures, and initial operational readiness for housing units.
Lists prerequisites for fan commissioning and procedures for testing performance and motor rotation.
Details commissioning checks for belt tension and alignment for V-belts and flat belts.
Instructs on checking the sound attenuator for contaminants and damage before operation.
Covers filter selection, replacement criteria based on pressure drop, and installation checks.
Provides instructions for cleaning, commissioning, and frost protection of water coils.
Explains the function, cleaning, and installation direction of droplet separators.
Refers to specific instructions for cooling system commissioning, service, and maintenance due to design variations.
Details commissioning steps, water quality, and operational checks for humidifiers.
Guides on commissioning louver dampers, checking seating, movement, and positioning.
Covers safe cleaning, commissioning checks, and maintenance for rotary heat exchangers.
States that commissioning, service, and maintenance for plate heat exchangers follow guidelines for louvre dampers.
Advises on draining or filling with frost protection media and checking heat carrier medium effectiveness.
Details safety regulations, installation, commissioning, and exhaust gas value determination for direct lighted burners.
Outlines regulations, installation, commissioning, and operational readiness for gas surface burners.
Provides guidance on appropriate cleaning agents for different component materials.
Covers general installation, commissioning, and safety checks for control equipment and functions.
Lists tasks for decommissioning a unit for a lengthy period, including energy shut-off and fluid draining.
Describes procedures for professional dismantling and disposal of the equipment and its operating media.
Details fire prevention regulations and immediate actions during a fire incident, including power interruption.
Addresses risks from toxic substances and smoke during fire incidents and recommends protective equipment.
Specifies requirements for personnel, work environment, and procedures during service in potentially explosive atmospheres.
Explains identification markings for atmospheres and warning notices on equipment for explosion safety.
Details measures to avoid ignition sources from fans, electrical components, and hot surfaces in explosive atmospheres.
To Next Page
