SWS SeceuroGlide Classic User Manual

1
August 2016 Issue 1 SGEX16
SeceuroGlide Classic &
SeceuroGlide Excel Installation Instructions
Always check on delivery that the order details are correct and the
door is undamaged, especially before removing any existing doors.
Sequence of Installation & Contents
01. Pre-Installation and Component Check
02. Installation Options and Criteria for Compliance with LPS 1175
03. Prepare the Opening
04. Prepare the Guide Rails
05. Fit End Plates, Axle Assembly, Guides (& optional fascia)
06. Fitting Emergency Overrides
07. Install the Curtain in the Guides, Attach to Axle & Fit Stops
08. Curtain Locking & Setting Motor Limit Switches
09. Curtain Adjustment (reducing height/making repairs)
10. Installation of Box Supports
11. Commissioning
12. Technical Assistance
01. PRE-INSTALLATION AND COMPONENT CHECK
Check:
i. Delivery note
ii. Order sheet
iii. Door dimensions / colour
iv. Opening dimensions / clearances
v. Components
vi. Check for any damage to the guide rails
or the outside roll of the curtain
Do not proceed further with the
installation unless you are sure that
the door is the correct size, and all
components are present.
Total Height
Ground Height
Headroom
Drive Through Height
Drive Through Width
Over Guide Width
HEIGHTS
Order Height = Guide Height
Total Height = Guide Height + End Plate
Headroom/End Plate
up to 2.5m Guide Height = 300mm
up to 3.5m Guide Height = 350mm
Drive Through Height
Guide Height less 55mm
WIDTHS
Order Width = Over Guide Width
Drive Through Width
Over Guide Width less 150mm for 75mm guides
Over Guide Width less 180mm for 90mm guides
www.samsondoors.co.uk
0800 328 6250
www.samsondoors.co.uk

SWS SeceuroGlide Classic Specifications

General

Brand	SWS
Model	SeceuroGlide Classic
Category	Garage Door Opener
Language	English

Summary

01. Pre-Installation and Component Check

Electric Roller Garage Door Components

Lists all parts included in the roller garage door package for pre-installation verification.

Widths and Heights Definitions

Defines door measurements for widths and heights, including drive-through dimensions.

02. Installation Options and LPS 1175 Criteria

Internal, Face, and Reveal Fit Options

Details fitting methods for guide rails and compliance with LPS 1175 security standards.

Alternative Installation Options (Not LPS 1175 Compliant)

Outlines external installation and non-compliant face/reveal fits for non-security applications.

03. Prepare the Opening

04. Prepare the Guide Rails

Drilling and Fixing Guide Rails

Instructions for drilling holes and fixing guide rails, including LPS 1175 compliance.

05. Fit End Plates, Axle Assembly, Guides (& Optional Fascia)

Axle Assembly and Locking

Steps for fitting end plates, axle, guides, and securing the axle assembly.

Motor Power Lead and Anti-Fall Back Spring

Instructions for securing motor lead and tensioning anti-fall back spring.

06. Fitting Emergency Overrides

Standard Manual Override

How to fit the standard manual override eye and crank handle.

Optional External Low Level Override

Information on the optional external override kit and its compliance.

07. Install the Curtain in the Guides, Attach to Axle & Fit Stops

Curtain Attachment to Axle and Locking

Guide on attaching the curtain to the axle using locking collars and arms.

Fitting Stops and LPS 1175 Compliance Label

Instructions for fitting bottom slat stops and applying the LPS 1175 compliance label.

08. Curtain Locking & Setting Motor Limit Switches

Setting Motor Limit Switches

Procedure for setting the open and close limits for the motor.

09. Curtain Adjustment (Reducing Height/Making Repairs)

Adjusting Curtain Height and Slat Replacement

Guide on how to adjust curtain height and replace damaged slats.

10. Installation of Box Supports

11. Commissioning

Final Checks and Internal Fitting

Procedures for final checks, internal fitting, and demonstrating manual override.

12. Technical Assistance