Need help?Do you have a question about the tau K206MA and is the answer not in the manual?
Essential safety measures and precautions for installation and use.
Statement on manufacturer's responsibility for improper use or installation.
Procedures for verifying mechanical setup and system earthing.
Guidelines for proper cable selection and usage to prevent issues.
Details for connecting photocells (7-9) and sensitive edge (7-10).
Information on AUX, TX Photocell, and Flashing Light connections.
Connections for electromagnet (16-17) and bar LED (16-18).
Wiring for radio, aerial, motor, and encoder connections (19-32).
Explanation of T.R.A., T.C.A., and F.R. trimmer functions and adjustments.
Guide to configuring the control unit using dip switches 1 through 8.
Table detailing dip switch configurations for barrier models and lengths.
Setting for resistive or fixed sensitive edge using dip switch 12.
Ensuring mechanical balance and limit switches are correctly set.
Step-by-step guide to programming the automation limits and parameters.
How to stop or restart the memorization process, including error handling.
Configuration of automatic opening/closing cycles using a timer.
Functionality of the integrated battery charger and voltage monitoring.
Setting and function of obstacle detection via FR trimmer.
Interpretation of LEDs indicating status of input buttons and safety devices.
LED codes for battery charge status and system voltage.
LED codes for board logic errors and operational status.
Detailed interpretation of DL8 LED flashes for various error conditions.
Codes indicating factory reset or radio channel cancellation.
Monitoring motor absorption to assess motor stress during operation.
How to activate the function and interpret the DL7/DL8 LED indicators.
Procedures after manual operation or mains power failure for realignment.
Step-by-step guide for associating radio control devices with the receiver.
Procedure for remote self-learning of new transmitters.
Instructions for deleting programmed radio control devices.
Information on upgrading the code memory capacity with expansion cards.
Procedure for resetting the radio receiver memory.
Procedure for performing a factory reset of the control unit.
Troubleshooting steps for when the automation fails to initiate.
Causes and solutions for limited range of radio control operation.
Procedure to correct the gate opening or closing in the wrong direction.
Details of the product guarantee period and what it covers.
Cases and conditions not covered by the product warranty.
Essential safety measures and precautions for installation and use.
Statement on manufacturer's responsibility for improper use or installation.
Procedures for verifying mechanical setup and system earthing.
Guidelines for proper cable selection and usage to prevent issues.
Details for connecting photocells (7-9) and sensitive edge (7-10).
Information on AUX, TX Photocell, and Flashing Light connections.
Connections for electromagnet (16-17) and bar LED (16-18).
Wiring for radio, aerial, motor, and encoder connections (19-32).
Explanation of T.R.A., T.C.A., and F.R. trimmer functions and adjustments.
Guide to configuring the control unit using dip switches 1 through 8.
Table detailing dip switch configurations for barrier models and lengths.
Setting for resistive or fixed sensitive edge using dip switch 12.
Ensuring mechanical balance and limit switches are correctly set.
Step-by-step guide to programming the automation limits and parameters.
How to stop or restart the memorization process, including error handling.
Configuration of automatic opening/closing cycles using a timer.
Functionality of the integrated battery charger and voltage monitoring.
Setting and function of obstacle detection via FR trimmer.
Interpretation of LEDs indicating status of input buttons and safety devices.
LED codes for battery charge status and system voltage.
LED codes for board logic errors and operational status.
Detailed interpretation of DL8 LED flashes for various error conditions.
Codes indicating factory reset or radio channel cancellation.
Monitoring motor absorption to assess motor stress during operation.
How to activate the function and interpret the DL7/DL8 LED indicators.
Procedures after manual operation or mains power failure for realignment.
Step-by-step guide for associating radio control devices with the receiver.
Procedure for remote self-learning of new transmitters.
Instructions for deleting programmed radio control devices.
Information on upgrading the code memory capacity with expansion cards.
Procedure for resetting the radio receiver memory.
Procedure for performing a factory reset of the control unit.
Troubleshooting steps for when the automation fails to initiate.
Causes and solutions for limited range of radio control operation.
Procedure to correct the gate opening or closing in the wrong direction.
Details of the product guarantee period and what it covers.
Cases and conditions not covered by the product warranty.
General| Brand | tau |
|---|---|
| Model | K206MA |
| Category | Control Panel |
| Language | English |
To Next Page
