Teac X-2000R Service Manual

X-2000R
2-10 REEL TABLE HEIGHT ADJUSTMENT
1.
Adjust the tension arm height beforehand (See 2-9).
2. Check each reel table height using a TEAC RE-1002 empty reel
and letting the tape run in each tape operating mode.
If the tape rubs against the reel flanges, adjust the reel table
height by means of the two reel table mounting screws.
2-10 YV-L ARs
1. APHOS VY aL P-L AMRIT REET OTS
au.
2.TEAC
RE-1002U
—JL@#L,
SF
—PRMETT—
FH
Y—JL-
DOV
VITRMITSHDESDEFIVITS.
3.8
Lik
SBS
IS
IV
G
EME
LTS
2KDOKRVE
S60,
VIVE
RALBEHD
LTMETS.
standard empty reel
Fig. 2-11
2-11 TAPE PATH ALIGNMENTS
The following procedure is for parallelism adjustment of left pinch
roller. A similar procedure is also applied for the right pinch roller.
2-11-1 COARSE ADJUSTMENT OF PINCH ROLLER
1.
2.
PARALLELISM
Let pinch roller draw near toward capstan shaft by manually lift-
ing up tape lifter shown in Fig. 2-12.
Check pinch roller/capstan shaft parallelism viewed from direc-
tion of arrow A shown in Fig. 2-12. (Refer to Fig. 2-13, 14.)
If not parallel, joosen the reinforcement plate screw near the
correction-required side (Refer to Fig. 2-15), then correct tilt of
pinch roller spindle using correction jig. (Part No. 573600010).
Adjustment can be done by tilting correction jig in direction of
arrow Aor A’.
NOTE:
(1) Use the jig as near as possible to the pinch roller spindle.
(2) Do not touch the surface of spindle.
(3) Use no other tool for this adjustment.
Remove pinch roller, then push up tape lifter to visually align
pinch roller spindle with the capstan shaft viewed from direction
of arrow in Fig. 2-12.
If needed, adjust by tilting correction jig in direction of arrow B
or B’ in Fig, 2-15.
2-11-2. FINE ADJUSTMENT OF PINCH ROLLER
1,
2.
PARALLEL ALIGNMENT
Repeat fast winding and rewinding and confirm tape travel
Positioning does not vary.
If necessary, adjust pinch roller alignment as shown in Fig. 2-15.
reel table
2-11 F—-PHEAMES
EVF O-DSEtpPIZIY VrpIbhEeoVRitKkls, T—
DHTAOREICRELBEGIORTS.
LPR ICHEDF-O-SOF GT ERBOFIRERNETM, G
EVF-O-DITIW THMARIC HHL TRS.
Q-li-1 EY F O-FSPHEORME
1.§2-12CROF—T- VOSS FTULIT, EV F-O—
SeFpTIAZPU- VIbITMIGS.
2.M2-12CRFAHMPSET, EV F- -O-SttrIAP
VY VpThOVFATREFLIVIFTS.
3. CEB IS, PRBS L TM2-15icmg, AX
ISA AMICK LVF - O-SHOMe GEES S. (PHM IS
WRSEGEVF - O-DeHED MR lOey hUTKS
U)). (GARE 5425736000100)
4iKITEVF-O-SEWRL, F-T- UDSEEV, 2-12
MBAMDSATEVF-O-SEFPTIAZIY- VePIb
MOATEEFIVItS.
FICEUBRI, MRSS HAL CM2-15icmsg BAIS
BARAMICELDF-O—DSHOMS SHEIET S.
2-11-2 Ev F -02-FRG RRS :
1.FWD, REV &#8K UF — DHA ORIEL EUT & EE
BTS.
2.6 LEIS SBF ISM 2-LOHET ELV F:- O-— SHORES
& MASS.

Teac X-2000R Specifications

General

Track system	4-track, 2-channel stereo
Reel size	Up to 10.5 inch reel
Total harmonic distortion	0.8%
Type	Reel-to-reel tape deck
Tape speeds	9.5 cm/s, 19 cm/s
Wow and flutter	0.03% (19 cm/s)
Signal to Noise Ratio	58dB
Inputs	Line input (RCA), microphone input (XLR)
Outputs	Line output (RCA), headphone output (6.3mm jack)