EasyManuals Logo
Home>Technics>Headphone>EAH-AZ70W

Technics EAH-AZ70W User Manual

Technics EAH-AZ70W
30 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #13 background imageLoading...
Page #13 background image
Preparation
13
3
Confirm that the earphone LEDs (red) have illuminated (charging starts).
The earphone LEDs light (red) while the earphones are charging. Charging is complete when they turn off.
Charging time (
l 26, “Specifications”)
Note
Do not use any other USB charging cords except the supplied one. Doing so may cause malfunction.
Charging may not be performed or may stop if the computer is in or switched to standby or sleep mode.
Earphones can only be charged with a charged charging cradle. You can charge your earphones while you are
out, even if there is no power source.
When the charging cradle is fully charged, it can charge the earphones about 2 times.
1
Put the earphones into the charging cradle.
The earphones LEDs light (red). Refer to Step 2 on page 12 for how they light.
2
Confirm that the earphone LEDs (red) have illuminated. (charging starts)
The earphones LEDs light (red) while the earphones are charging. Charging is complete when they turn off.
It takes approx. 2 hours to charge the earphones from empty to full.
The LEDs lighting or flashing on this unit indicate the remaining battery charge.
Earphones
When the battery level starts to run low while you are using the earphones, the blinking earphone LEDs change
from blue to red, then you will be notified by one beep every 5 minutes. When no charge remains, you will hear
a guidance message and then the unit automatically turns off.
Charging cradle
When you open the charging cradle lid, the charging cradle LEDs light or blink to indicate the charge remaining
in the battery.
When 1 charging cradle LED is blinking, the charge in the battery is even lower. Charge the unit.
If the charging cradle LEDs do not light even when you open the charging cradle lid, there is no charge in the battery.
Charge the unit.
Charging the earphones with the charging cradle
Battery level notification
Status of the charging cradle
LEDs
Remaining battery charge
3 light
1 lights
There is plenty of charge in the battery.
The charge in the battery is running low. You should charge the unit.

Other manuals for Technics EAH-AZ70W

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Technics EAH-AZ70W and is the answer not in the manual?

Technics EAH-AZ70W Specifications

General IconGeneral
Cable length0.5 m
Control typeTouch
Headset typeBinaural
Product typeHeadset
Product colorSilver
Wearing styleIn-ear
Recommended usageCalls/Music
Works with the Google AssistantYes
International Protection (IP) codeIPX4
Battery typeBuilt-in battery
Battery recharge time2 h
Continuous audio playback time6.5, 7.5 h
Battery recharge time (charging case)2.5 h
Continuous audio playback time (with charging case)19.5 h
Wireless range10 m
3.5 mm connectorNo
USB connectivity-
Bluetooth version5.0
Bluetooth profilesA2DP, AVRCP, HFP, HSP
Connectivity technologyWireless
Impedance- Ω
Driver unit10 mm
Magnet typeNeodymium
Ear couplingIntraaural
Headphone frequency20 - 20000 Hz
Cables includedUSB
Charging case typeWired
Charging case connector typeUSB Type-C
Microphone typeBuilt-in
Weight and Dimensions IconWeight and Dimensions
Charging case weight65 g
Left earpiece weight7 g

Related product manuals