EasyManuals Logo
Home>Technics>Headphone>EAH-AZ70W

Technics EAH-AZ70W User Manual

Technics EAH-AZ70W
30 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #24 background imageLoading...
Page #24 background image
Other
24
Troubleshooting
Before requesting service, make the following checks. If you are in doubt about some of the check points, or if
the remedies indicated in the chart do not solve the problem, refer to “Customer Services Directory” if you
reside in the U.S.A., or refer to “CONTACT INFORMATION” if you reside in Canada. (Refer to “Limited
Warranty”.)
No sound.
Make sure that the earphones and the Bluetooth
®
device are connected correctly. (l 16)
Check if music is playing on the Bluetooth
®
device.
Make sure that the earphones are turned on and the volume is not set too low.
Pair and connect the Bluetooth
®
device and the earphones again. (l 16)
Check if the Bluetooth
®
compatible device supports “A2DP” profile. For details on profiles, see “Listening to music”
(
l 18). Also refer to the operating manual for the Bluetooth
®
compatible device.
Low volume.
Also raise the volume on the Bluetooth
®
device, not just on the earphones.
Sound from the device is cut off. / Too much noise. / Sound quality is bad.
Sound may be disrupted if signals are blocked. Do not fully cover the earphones with the palm of your hand, etc.
The device may be out of the 10 m (33 ft) communication range. Move the device closer to the earphones.
Remove any obstacle between the earphones and the device.
Switch off any wireless LAN device when not in use.
The device cannot be connected.
You can pair a maximum of 10 Bluetooth
®
devices with the earphones. When you pair a device after the maximum
has been exceeded, previous devices are overwritten. To use overwritten devices again, do the pairing again.
Delete the pairing information for this unit from the Bluetooth
®
device, then pair them again. (l 16)
The voice of the person on the other end of the call is small.
Also raise the volume on the Bluetooth
®
device, not just on the earphones.
Cannot make a phone call.
Check if the Bluetooth
®
compatible device supports “HSP” or “HFP” profile. For details on profiles, see “Listening to
music” (
l 18) and “Making a phone call” (l 19). Also refer to the operating manual for the Bluetooth
®
enabled
phone.
Check the audio settings on the Bluetooth
®
compatible telephone, and if the setting does not allow communication
with this unit, change the setting. (
l 16)
Sound and audio volume
Bluetooth
®
device connection
Phone Calls

Other manuals for Technics EAH-AZ70W

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Technics EAH-AZ70W and is the answer not in the manual?

Technics EAH-AZ70W Specifications

General IconGeneral
Cable length0.5 m
Control typeTouch
Headset typeBinaural
Product typeHeadset
Product colorSilver
Wearing styleIn-ear
Recommended usageCalls/Music
Works with the Google AssistantYes
International Protection (IP) codeIPX4
Battery typeBuilt-in battery
Battery recharge time2 h
Continuous audio playback time6.5, 7.5 h
Battery recharge time (charging case)2.5 h
Continuous audio playback time (with charging case)19.5 h
Wireless range10 m
3.5 mm connectorNo
USB connectivity-
Bluetooth version5.0
Bluetooth profilesA2DP, AVRCP, HFP, HSP
Connectivity technologyWireless
Impedance- Ω
Driver unit10 mm
Magnet typeNeodymium
Ear couplingIntraaural
Headphone frequency20 - 20000 Hz
Cables includedUSB
Charging case typeWired
Charging case connector typeUSB Type-C
Microphone typeBuilt-in
Weight and Dimensions IconWeight and Dimensions
Charging case weight65 g
Left earpiece weight7 g

Related product manuals