To Next Page

To Previous Page

Table of Contents

TDS 500B, 600B and TDS 700A Service Manual

vii

List of Tables

Table 1–1: Key Features of the TDS 500B, 600B and 700A

Oscilloscopes 1–1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 1–2: Record Length vs. Divisions per Record, Samples per

Division and Sec/Div Sequence 1–3. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 1–3: Nominal Traits — Signal Acquisition System 1–9. . . . . . . . . .

Table 1–4: Nominal Traits — Time Base System 1–10. . . . . . . . . . . . . . . .

Table 1–5: Nominal Traits — Triggering System 1–11. . . . . . . . . . . . . . . .

Table 1–6: Nominal Traits — Display System 1–12. . . . . . . . . . . . . . . . . . .

Table 1–7: Nominal Traits — GPIB Interface, Output Ports, and

Power Fuse 1–12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 1–8: Nominal Traits — Data Handling and Reliability 1–12. . . . . .

Table 1–9: Nominal Traits — Mechanical 1–13. . . . . . . . . . . . . . . . . . . . . .

Table 1–10: Warranted Characteristics — Signal Acquisition

System 1–16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 1–11: Warranted Characteristics — Time Base System 1–17. . . . . .

Table 1–12: Warranted Characteristics — Triggering System 1–18. . . . .

Table 1–13: Warranted Characteristics — Output Ports, Probe

Compensator, and Power Requirements 1–18. . . . . . . . . . . . . . . . . . . .

Table 1–14: Warranted Characteristics — Environmental 1–19. . . . . . . .

Table 1–15: Typical Characteristics — Signal Acquisition System 1–23. .

Table 1–16: Typical Characteristics — Triggering System 1–27. . . . . . . .

Table 2–1: Power-Cord Conductor Identification 2–2. . . . . . . . . . . . . . . .

Table 2–2: Power Cord Identification 2–2. . . . . . . . . . . . . . . . . . . . . . . . .

Table 2–3: Effects of Corrupted Data 2–4. . . . . . . . . . . . . . . . . . . . . . . . . .

Table 4–1: Test Equipment 4–16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 4–2: DC Offset Accuracy (Zero Setting) 4–28. . . . . . . . . . . . . . . . . .

Table 4–3: DC Voltage Measurement Accuracy 4–31. . . . . . . . . . . . . . . . .

Table 4–4: Analog Bandwidth 4–35. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 4–5: Delay Between Channels Worksheet 4–42. . . . . . . . . . . . . . . . .

Table 5–1: Calibration Tests 5–3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 5–2: Adjustments Required for Module Replaced 5–4. . . . . . . . . .

Table 5–3: Adjustments and Dependencies 5–4. . . . . . . . . . . . . . . . . . . . .

Table 5–4: Test Equipment, Fixtures, and Supplies 5–5. . . . . . . . . . . . . .

Table 5–5: GPIB Board Configuration 5–7. . . . . . . . . . . . . . . . . . . . . . . . .

Tektronix TDS 700A Service Manual

Other manuals for Tektronix TDS 700A