Teledyne T700 - User Manual

To Next Page

User Manual

Models T700 and T700U

Dynamic Dilution Calibrators

with NumaView™ Software

9970 CARROLL CANYON ROAD

SAN DIEGO, CALIFORNIA 92131-1106

USA

Toll-free Phone:

+1 800-324-5190

Phone:

+1 858-657-9800

Fax:

+1 858-657-9816

Email:

api-sales@teledyne.com

Website:

http://www.teledyne-api.com/

Teledyne API 16 January 2020

Main Page

User Manual1
Models T700 and T700U1
Dynamic Dilution Calibrators1
- Notice of Copyright3
- Trademarks3
Important Safety Information4
Consignes de Sécurité5
Warranty Statement6
Conventions Used in This Manual7
Table of Contents8
List of Figures13
List of Tables16
List of Appendices17
1. Introduction, Specifications and Approvals18
- 1.1. Calibrator Overview18
- 1.2. Features18
- 1.3. Options19
- 1.4. T700 Specifications21
- 1.5. T700U Specifications23
- 1.6. Approvals and Certifications25
2. Getting Started26
- 2.1. Unpacking26
  - 2.1.1. Ventilation Clearance27
- 2.2. Instrument Layout27
- 2.3. Connections33
  - 2.3.1. Electrical Connections33
  - 2.3.2. Pneumatic Connections46
- 2.4. Startup and Functional Checks65
- 2.5. Menu Overview71
- 2.6. Setup Menu: Features/Functions Configuration81
- 2.7. Transferring Configuration to Other Instruments102
3. Operating Modes, Basic Operation, and Configurations103
- 3.1. STANDBY MODE104
- 3.2. GENERATE MODE105
4. Communications and Remote Operation126
- 4.1. Data Terminal/Communication Equipment (DTE DCE)126
- 4.2. Modes, Baud Rate and Serial Communication126
  - 4.2.1. Serial Communication: RS-232126
  - 4.2.2. Serial Communication: RS-485 (Option)127
- 4.3. Ethernet127
- 4.4. MODBUS Communications Protocol127
  - 4.4.1.1. MODBUS Com Port Configuration128
5. Calibration and Verification130
- 5.1. Verifying and Calibrating the MFCs130
  - 5.1.1. Setup for Verifying and Calibrating the MFCs131
  - 5.1.2. Verifying and Calibrating the MFCs132
- 5.2. Verifying and Calibrating the O3 Photometer (Bench) Option133
- 5.3. Verifying and Calibrating the O3 Generator Option140
- 5.4. Verifying and Calibrating the Gas Pressure Sensors141
  - 5.4.1.1. Calibrating Diluent, Cal Gas, or Opt O3 Generator Pressure Sensors143
  - 5.4.1.2. Calibrating the Photometer (Option) Sample Gas Pressure Sensor144
6. Maintenance145
- 6.1. Maintenance Schedule145
- 6.2. Operational Health Checks147
- 6.3. Software/Firmware Updates148
- 6.4. Time Zone Changes150
- 6.5. Maintenance Procedures151
7. Troubleshooting and Service159
- 7.1. General Troubleshooting159
- 7.2. Using the Internal Electronic Status LEDs165
- 7.3. Subsystem Checkout169
- 7.4. TroubleShooting the Optional O3 Photometer180
  - 7.4.1. Dynamic Problems with the Optional O3 Photometer180
  - 7.4.2. Checking The UV Lamp Power Supply182
- 7.5. TroubleShooting the Optional O3 generator183
  - 7.5.1. Checking The UV Source Lamp Power Supply183
- 7.6. Replacing the Disk-on-Module184
- 7.7. Technical Assistance184
- 7.8. Frequently Asked Questions (FAQs)185
8. Principles of Operation186
- 8.1. Basic Principles of Dynamic Dilution Calibration186
  - 8.1.1. Gas Phase Titration Mixtures for O3 and NO2187
- 8.2. Pneumatic Operation188
  - 8.2.1. Gas Flow Control188
  - 8.2.2. Internal Gas Pressure Sensors191
- 8.3. Electronic Operation192
- 8.4. Software Operation203
- 8.5. O3 Generator Operation204
- 8.6. Photometer Operation208
Glossary216
Note: Some terms in this glossary may not occur elsewhere in this manual.216

Teledyne T700 - User Manual

Table of Contents

Other manuals for Teledyne T700

Related product manuals