What to do if there is no picture on my Televes zAshd Receiver?
If there's no picture on your Televes Receiver, first, ensure the receiver is powered on by pressing the power key on the RCU. Next, check that the HDMI and/or SCART cables are firmly connected. Finally, make sure the cable from the antenna is securely connected to your receiver.
Why is there no sound on my Televes zAshd?
If there's no sound or the sound is too low on your Televes Receiver, check the volume levels on both your TV and the receiver to ensure they are not set too low or muted. Also, verify that the SCART or HDMI cable is securely connected.
How to fix a Televes zAshd RCU that is not working?
If your Televes Receiver remote control unit (RCU) isn't working, start by checking the battery status. If the batteries are exhausted, replace them. Also, ensure that you are pointing the RCU directly at the receiver without any obstacles in the way.
What to do if my Televes zAshd says 'No channels were found'?
If, after completing the channel search on your Televes Receiver, a message reads “No channels were found,” or some channels are missing, ensure that your antenna is properly connected to your receiver. Also, verify that the cable from the LNB is connected to the receiver input connector, and that the options selected in the “Setting antenna” menu correspond to your installation.
Why the image on my Televes Receiver is pixelated?
If the image on your Televes Receiver is broken and appears in blocks (pixeling), and your installation is complex, try connecting your receiver the simplest way possible (receiver + TV) by directly connecting the antenna to your receiver. If the image is no longer interrupted, then its signal does not have enough power to use a facility so complex. Also, damaged cables and connectors can affect signal quality, so consider changing them.
How to fix distorted image on Televes zAshd Receiver?
If the image on your Televes Receiver appears distorted or moved sideways, it might be due to the display format being set to 4:3 while the program is broadcast in 16:9. To resolve this, change the display format to “Letterbox” or “Pan & Scan” in the “Output Settings” menu.
Why can't I watch digital channels on my Televes zAshd after moving?
If you've moved your Televes Receiver to another home and can't watch digital channels, it could be that the antenna isn't aiming at the same satellite. In this case, perform a new channel search. It might also be that the installation of the house is not adequate to receive digital satellite channels.
How to turn on Televes zAshd if the front panel LED is off?
If the front panel LED on your Televes Receiver is off, ensure that the power cord is properly connected. Make sure the adapter is plugged in and connected to the receiver.
What does a red front panel LED on Televes zAshd mean?
If the front panel LED on your Televes Receiver glows red, the receiver is likely in stand-by mode. Press the power key on the remote control unit (RCU) to power on the receiver.
Key features and capabilities of the ZAS HD SAT receiver.
Overview of ports and indicators on the front of the ZAS HD SAT receiver.
Identification and function of the rear panel connections for the ZAS HD SAT.
Explanation of buttons and functions of the ZAS HD SAT remote control.
Guide on how to connect the ZAS HD SAT receiver to your TV.
Configuring antenna types and performing automatic or manual channel searches.
Updating software via USB and resetting receiver to factory defaults.
Using the TimeShift function to pause and resume live TV broadcasts.
General| DiSEqC | 1.0, 1.1, 1.2 |
|---|---|
| Demodulation | DVB-S, DVB-S2 |
| Symbol Rate | 2~45Msps |
| Video Decoding | MPEG-2 |
| Audio Decoding | MPEG-1/2 Layer I/II, AAC |
| Video Output | HDMI, CVBS |
| Audio Output | HDMI, RCA |
| USB | USB 2.0 |
| Power Supply | 12 V DC, 1.5 A |
| Input Frequency Range | 950-2150 MHz |
| Connectors | HDMI, RCA, USB |
| Operating Temperature | 0°C to +40°C |
To Next Page
