To Next PageTo Next PageWhat to do if my Thermo King Automobile Accessories unit did not start automatically?
If the unit did not start automatically, determine the cause for not starting. Correct as required. Continue monitoring return air temperature until reading is within desired temperature range of the setpoint.
What to do if the Thermo King Automobile Accessories return air temperature is not within the desired range?
If the return air temperature is not within the desired range, several factors could be the cause. First, review the load log history for above-temperature load records to ensure the cargo compartment was properly pre-cooled and consider the length of time on the road. If the unit is in defrost or has just completed a defrost cycle, monitor the return air temperature after the defrost cycle is completed to see if the temperature returns to the desired temperature range of the setpoint. Also, the evaporator may be plugged with frost, so initiate a manual defrost cycle. Finally, inspect the unit and cargo compartment to ensure the evaporator fans are working properly and that air circulation is not blocked by improper loading or shifting cargo.
Why is my Thermo King Automobile Accessories not cooling to the set temperature?
Several factors can prevent your Thermo King unit from cooling to the set temperature. The unit may have a low refrigerant charge; check the receiver tank sight glass for refrigerant level. If fluid is not showing, a competent refrigeration technician is required to add refrigerant or repair the system. Improper air circulation in the cargo compartment may also be the reason. Inspect the unit and cargo compartment to determine if the evaporator fans are working properly circulating the air. Poor air circulation may be due to improper loading of the cargo, shifting of the load, or fan belt slippage. Correct as required.
Why my Thermo King Automobile Accessories multi-temp unit can't cool the entire trailer?
A multi-temperature unit may not have the cooling or heating capacity to maintain a specific temperature range throughout an entire trailer if it is being used to cool/heat a single temperature load.
Mechanism for users to provide feedback on manuals via an online survey.
Basic safety rules for operating and servicing Thermo King units.
Warning about automatic unit starts and the procedure to safely shut down.
Safety guidelines for installing batteries and routing cables to prevent hazards.
Warnings and precautions for handling refrigerants, including toxic gas and suffocation risks.
Safety precautions for working with refrigerant oil, including eye, skin, and clothing protection.
First aid procedures for refrigerant or oil exposure to eyes, skin, or inhalation.
Information on the location and purpose of safety decals on the unit.
Awareness of warning nameplates regarding hazards associated with fans.
Safety warnings for units equipped with remote start and telematics, focusing on automatic starts.
Prohibition of ether starting aids due to the risk of fire or explosion.
Overview of SLXi models, their self-contained design, and control system.
Details on the 4-cylinder diesel engine, Extended Life Coolant (ELC), and EMI 3000 package.
Description of the reciprocating compressor, electronic throttling valve, and SR-3 control system.
Explanation of CYCLE-SENTRY modes, continuous run, and standard TK BlueBox telematics.
Details on ServiceWatch, CargoWatch, data transfer methods, and OptiSet Plus.
Description of ServiceWatch for recording operating events and diagnosing issues.
Information on CargoWatch for logging temperature and event data with optional sensors.
Methods for accessing data, including Printer Port, USB, GPRS, and wireless connections.
Explanation of OptiSet Plus for programmable unit operation based on setpoints or products.
Explanation of automatic and manual defrost cycles for evaporator coils.
Visual checks of maintenance items within the engine compartment.
Descriptions of various devices protecting the unit, such as coolant, temperature, pressure, and oil switches.
Information on the preheat buzzer, automatic reset overload relay, and Smart FETs.
List of fuses, their sizes, and functions within the unit's electrical system.
Specific Optiset profiles for pharmaceutical applications and recommended setpoints.
Essential checks before unit operation, including fuel, oil, coolant, and battery.
Inspection of belts, electrical connections, and structural integrity for damage or leaks.
Guidelines for cleaning condenser and evaporator coils, including pressure washer use.
Checks for cargo box damage, door seals, and damper door operation.
Inspection of defrost drains and remote evaporator units for blockages or leaks.
Procedure for verifying the TK BlueBox module is powered on and communicating.
Introduction to the SR-3 controller for temperature management and unit operation.
Description of the Human-Machine Interface control panel, its display, and graphical capabilities.
Explanation of the dedicated and soft keys on the HMI control panel and their functions.
Steps for operating the SR-3 controller and changing the display language.
Procedure to access the language menu and select a preferred language.
Instructions for connecting a printer to the SLX unit to print trip data.
Explanation of alarm generation, storage, and the importance of documenting alarm occurrences.
Procedures for inspecting products and the trailer prior to loading cargo.
Steps to verify proper cargo loading and unit readiness after loading.
Guidelines for conducting regular inspections during transit to minimize temperature issues.
Steps to diagnose and resolve temperature-related problems encountered during enroute inspections.
Functionality of the LVD switch for third-party connections and battery protection during idle periods.
Detailed, step-by-step instructions and safety warnings for jump starting a unit.
Details on the engine model, fuel type, oil capacity, and oil type.
Recommended oil viscosity based on ambient temperature and engine RPM ranges.
Information on engine coolant types, system capacity, and drive mechanisms.
Part numbers for filters and contact information for refrigeration system service.
Specifications for low voltage, battery, fuses, and battery charging systems.
Technical details for the electric motor, including size, speed, voltage, and load amps.
Requirements for standby power, including circuit breakers and power cord sizes.
Details on the TK BlueBox platform, communication modules, and backup battery.
Table outlining interim, complete PM, and full service intervals based on hours or age.
Guidance on recording all inspection and service activities in the dealer service record.
Mechanism for users to provide feedback on manuals via an online survey.
Basic safety rules for operating and servicing Thermo King units.
Warning about automatic unit starts and the procedure to safely shut down.
Safety guidelines for installing batteries and routing cables to prevent hazards.
Warnings and precautions for handling refrigerants, including toxic gas and suffocation risks.
Safety precautions for working with refrigerant oil, including eye, skin, and clothing protection.
First aid procedures for refrigerant or oil exposure to eyes, skin, or inhalation.
Information on the location and purpose of safety decals on the unit.
Awareness of warning nameplates regarding hazards associated with fans.
Safety warnings for units equipped with remote start and telematics, focusing on automatic starts.
Prohibition of ether starting aids due to the risk of fire or explosion.
Overview of SLXi models, their self-contained design, and control system.
Details on the 4-cylinder diesel engine, Extended Life Coolant (ELC), and EMI 3000 package.
Description of the reciprocating compressor, electronic throttling valve, and SR-3 control system.
Explanation of CYCLE-SENTRY modes, continuous run, and standard TK BlueBox telematics.
Details on ServiceWatch, CargoWatch, data transfer methods, and OptiSet Plus.
Description of ServiceWatch for recording operating events and diagnosing issues.
Information on CargoWatch for logging temperature and event data with optional sensors.
Methods for accessing data, including Printer Port, USB, GPRS, and wireless connections.
Explanation of OptiSet Plus for programmable unit operation based on setpoints or products.
Explanation of automatic and manual defrost cycles for evaporator coils.
Visual checks of maintenance items within the engine compartment.
Descriptions of various devices protecting the unit, such as coolant, temperature, pressure, and oil switches.
Information on the preheat buzzer, automatic reset overload relay, and Smart FETs.
List of fuses, their sizes, and functions within the unit's electrical system.
Specific Optiset profiles for pharmaceutical applications and recommended setpoints.
Essential checks before unit operation, including fuel, oil, coolant, and battery.
Inspection of belts, electrical connections, and structural integrity for damage or leaks.
Guidelines for cleaning condenser and evaporator coils, including pressure washer use.
Checks for cargo box damage, door seals, and damper door operation.
Inspection of defrost drains and remote evaporator units for blockages or leaks.
Procedure for verifying the TK BlueBox module is powered on and communicating.
Introduction to the SR-3 controller for temperature management and unit operation.
Description of the Human-Machine Interface control panel, its display, and graphical capabilities.
Explanation of the dedicated and soft keys on the HMI control panel and their functions.
Steps for operating the SR-3 controller and changing the display language.
Procedure to access the language menu and select a preferred language.
Instructions for connecting a printer to the SLX unit to print trip data.
Explanation of alarm generation, storage, and the importance of documenting alarm occurrences.
Procedures for inspecting products and the trailer prior to loading cargo.
Steps to verify proper cargo loading and unit readiness after loading.
Guidelines for conducting regular inspections during transit to minimize temperature issues.
Steps to diagnose and resolve temperature-related problems encountered during enroute inspections.
Functionality of the LVD switch for third-party connections and battery protection during idle periods.
Detailed, step-by-step instructions and safety warnings for jump starting a unit.
Details on the engine model, fuel type, oil capacity, and oil type.
Recommended oil viscosity based on ambient temperature and engine RPM ranges.
Information on engine coolant types, system capacity, and drive mechanisms.
Part numbers for filters and contact information for refrigeration system service.
Specifications for low voltage, battery, fuses, and battery charging systems.
Technical details for the electric motor, including size, speed, voltage, and load amps.
Requirements for standby power, including circuit breakers and power cord sizes.
Details on the TK BlueBox platform, communication modules, and backup battery.
Table outlining interim, complete PM, and full service intervals based on hours or age.
Guidance on recording all inspection and service activities in the dealer service record.
General| Brand | Thermo King |
|---|---|
| Model | SLXi-100 |
| Category | Refrigerator |
| Language | English |
