To Next PageTo Next PageWhat to do if my Topper Water Filtration System won’t make water?
If your Topper Water Filtration System isn't producing water, it might be due to the leak switch being in the ‘OFF’ position. To resolve this, first remove any swollen leak pad. Then, switch the leak switch to the ‘ON’ position. Investigate for any leaks and repair them. After the repair, replace the leak pad and restart the system.
Provides essential operational details, usage guidelines, and cautions for the WOW RO System.
Highlights common installation errors to avoid for a successful setup and operation.
Outlines essential checks and supplies needed before beginning the installation process.
Details the components included in the installation kit, including faucet and tubing options.
Provides a legend for identifying parts within the installation kit, including different tubing and faucet types.
Instructs users on how to inspect system components and cartridges after unboxing for installation.
Illustrates the correct positioning of the PRE, RO, and POST filter cartridges on the manifold.
Guides users through the process of installing the filter and RO membrane cartridges correctly.
Details how to connect the various tubing lines to the WOW RO System manifold ports.
Provides step-by-step instructions for priming the system and ensuring proper initial operation.
Details the steps for attaching and integrating a leak detection system to the WOW RO 50 unit.
Explains how to physically mount and connect the leak detection system to the RO unit's base.
Guides users on how to initiate the system after the leak detection add-on is installed.
Emphasizes crucial final checks after installation to ensure the system is leak-free and operational.
Details the procedure for installing leak pads for the leak detection system's functionality.
Covers connecting one or multiple appliances, including important "Do's and Don'ts".
Provides guidance on assessing storage needs based on connected appliances and usage.
Details the process for connecting the RO system to refrigerators and icemakers for filtered water.
Explains how to remove air from lines connected to refrigerators/icemakers after installation.
Guides users on connecting the RO system to coffee makers for improved coffee quality.
Describes the procedure for purging air from the coffee maker connection line.
Explains how to connect the RO system to water coolers for purified water dispensing.
Details how to remove air from the water cooler connection line after installation.
Guides users on connecting the RO system to a hot water tank or dispenser.
Describes how to purge air from the hot tank connection line.
Explains the need for additional water storage and how to determine expansion requirements.
Provides instructions for connecting additional storage tanks to the RO system for increased capacity.
Illustrates system configurations for parallel processing of water through multiple units.
Details the proper installation procedure for the drain saddle assembly for waste water.
Guides users on preparing and installing the RO faucet, including drilling requirements.
Provides detailed instructions for removing and replacing the system's filter and RO membrane cartridges.
Specifies the recommended replacement intervals for each type of filter cartridge.
Describes the main components of the WOW RO System and the function of each filter type.
Details the procedure for sanitizing the RO system, typically done during filter replacement.
Suggests additional resources for comprehensive information on RO systems.
Outlines critical safety precautions and recommendations for using the RO appliance.
Lists the general provisions and conditions that must be met for the warranty to remain valid.
Provides space for recording installer/dealer information and service notes.
Contains logs for recording filter replacement dates and associated service details.
Lists the NSF/ANSI 58 standard requirements and the system's actual test results against them.
Details the main components and parts that make up the WOWROTM system assembly.
Provides information on the membrane's production rate and TDS reduction capabilities.
Outlines the specific contaminant reduction claims certified by NSF/ANSI 58 for the system.
Summarizes the key certification results, including production, recovery, and TDS reduction ratings.
Lists the operational parameters such as pH, pressure, temperature, and TDS limits for the system.
General| Brand | Topper |
|---|---|
| Model | WOW RO 50 |
| Category | Water Filtration Systems |
| Language | English |
