Why is my Toro 38812 Snow Blower leaving snow on the surface?
If your Toro Snow Blower isn't clearing snow properly off the surface, it might be due to: * Improperly adjusted skids and/or scraper. Adjust the skids and/or the scraper. * Unequal tire pressure. Check and adjust the pressure in one or both tires.
What to do if the electric starter on my Toro 38812 isn't working?
If the electric starter on your Toro Snow Blower isn't turning, check these items: * Make sure the power cord is connected at both the outlet and the machine. Connect the power cord to the outlet and/or the machine. * Inspect the power cord for wear, corrosion, or damage. Replace the power cord if needed. * Verify that the power outlet is energized. Have a qualified electrician energize the outlet if it is not.
What to do if my Toro Snowthrower is not throwing snow?
If your Toro Snowthrower runs but doesn't discharge snow well, consider these possible causes: 1. The throttle is not in the Fast position when throwing snow, so move the throttle to the Fast position. 2. The machine is moving too fast to clear the snow, so shift the machine into a lower gear. 3. You are trying to remove too much snow per swath, so reduce the amount of snow removed per swath. 4. You are trying to remove extremely heavy or wet snow, so don't overload the machine with extremely heavy or wet snow. 5. The discharge chute is plugged, so unclog the discharge chute. 6. The auger/impeller drive belt is loose or is off the pulley. 7. The auger/impeller drive belt is worn or broken.
Why Toro 38812 does not properly clear the snow off the surface?
To resolve the issue of the Toro Snow Blower not properly clearing snow, adjust the skids and/or scraper. Ensure that the tire pressure is equal in both tires.
What to do if my Toro Snow Blower does not discharge snow properly?
If your Toro Snow Blower isn't discharging snow well, ensure the throttle is in the Fast position and shift to a lower gear. Reduce the amount of snow you're trying to clear per pass, and avoid overloading the machine with heavy, wet snow. Check for and clear any blockage in the discharge chute. Inspect the auger/impeller drive belt; make sure it is properly installed and adjusted.
How to fix rough running engine on Toro 38812 Snow Blower?
If your Toro Snow Blower runs rough, ensure the choke is in the Off position and the fuel shutoff valve is fully open. Use fresh gasoline in the fuel tank. Check that the spark plug wire is securely connected and the spark plug is in good condition with the correct gap. Also, verify that the engine oil level in the crankcase is at the Full mark on the dipstick.
Why is my Toro 38812 Snow Blower not throwing snow?
If your Toro Snow Blower runs but doesn't discharge snow well, check these possible causes: * Ensure the throttle is in the Fast position when throwing snow. * If the machine is moving too fast, shift into a lower gear. * Reduce the amount of snow removed per swath if you're trying to remove too much at once. * Avoid overloading the machine with extremely heavy or wet snow. * Unclog the discharge chute if it's plugged.
General| Starting System | Recoil |
|---|---|
| Engine Type | 4-cycle OHV |
| Engine Displacement | 212cc |
| Starter Type | Recoil |
| Speed Settings | 6 Forward, 2 Reverse |
| Chute Control | Quick Lever |
| Engine | 212cc |
| Clearing Depth | 12.5 in (32 cm) |
| Weight | 84 lbs |
| Chute Rotation | 210 degrees |
| Throw Distance | Up to 35 feet |
| Intake Height | 12.5 in (32 cm) |
| Skid Shoes | Adjustable |
| Warranty | 2-Year Full Coverage |
To Next Page
