Why does my Toro 74938 Lawn Mower pull to one side?
If your Toro Lawn Mower pulls to the left or right with the motion-control levers fully forward, the tracking may need adjustment. Also, ensure that the tire pressure in the drive tires is correct.
Why won't my Toro Lawn Mower engine start, starts hard, or fails to keep running?
If your Toro Lawn Mower engine will not start, starts hard, or fails to keep running, fill the fuel tank, open the fuel shutoff valve and add oil to the crankcase. Ensure that the throttle control is midway between the “SLOW” and “FAST” positions. Also, replace the fuel filter, clean or replace the air cleaner element, check the seat switch indicator (replace the seat if needed), check the electrical connections for good contact (clean the connector terminals thoroughly with electrical contact cleaner, apply dielectric grease, and reconnect), clean, adjust, or replace the spark plug and check the spark plug wire connection. If problems persist, contact an Authorized Service Dealer.
What to do if my Toro 74938 is resulting in uneven cutting height?
If mowing with your Toro Lawn Mower results in an uneven cutting height, try the following: * Sharpen the blade(s). * Install new cutting blade(s). * Level the mower deck from side-to-side and front-to-rear. * Clean the underside of the mower. * Adjust the tire pressure.
Why does the engine lose power in my Toro Lawn Mower?
If your Toro Lawn Mower engine loses power, try the following: Reduce the ground speed. Clean the air cleaner element. Add oil to the crankcase. Remove any obstruction from the cooling fins and air passages. Clean or replace the fuel cap. Replace the fuel filter. If the problem continues, it is recommended to contact an Authorized Service Dealer.
Why is my Toro 74938 Lawn Mower resulting in uneven cutting height?
If your Toro Lawn Mower is mowing with an uneven cutting height, several factors could be responsible. Ensure the blades are sharp; if not, sharpen them. Bent cutting blades can also cause this, so install new ones. Check if the mower deck is level from side-to-side and front-to-rear, and adjust as needed. A dirty underside of the mower can interfere with cutting, so clean it. Also, verify that the tire pressure is correct. For a bent blade spindle, contact an Authorized Service Dealer.
How to fix uneven cutting height on Toro Lawn Mower?
To fix an uneven cutting height on your Toro Lawn Mower, start by sharpening any dull blades or installing new ones if bent. Ensure the mower deck is level from side-to-side and front-to-rear. Clean the underside of the mower deck, adjust the tire pressure to the correct level. For a bent blade spindle, contact an Authorized Service Dealer.
Why won't the blades rotate on my Toro 74938 Lawn Mower?
If the blades on your Toro Lawn Mower aren't rotating, consider these causes: * The mower deck belt may be worn, loose, or broken; install a new deck belt. * The mower deck belt may be off pulley; install the mower deck pulley and check the idler pulley, idler arm, and spring for correct position and function. * The pump drive belt may be worn, loose, or broken; check the belt tension or install a new belt. * The idler spring may be broken or missing; replace the spring.
Why is my Toro Lawn Mower engine losing power?
Your Toro Lawn Mower engine might be losing power due to several reasons: * The engine load could be excessive; reduce the ground speed. * The air cleaner might be dirty; clean the air cleaner element. * The oil level in the crankcase may be low; add oil to the crankcase. * The cooling fins and air passages above the engine could be plugged; remove the obstruction. * The vent hole in the fuel cap may be plugged; clean or replace the fuel cap. * There may be dirt in the fuel filter; replace the fuel filter.
How to fix uneven cutting height with my Toro Lawn Mower?
An uneven cutting height with your Toro Lawn Mower may be due to dull blades, bent cutting blades, an unlevel mower deck, a dirty mower underside, or incorrect tire pressure. Try to sharpen the blades, install new cutting blades, level the mower deck from side-to-side and front-to-rear, clean the underside of the mower, and adjust the tire pressure. For a bent blade spindle, contact an Authorized Service Dealer.
What to do if my Toro 74938 doesn't drive?
If your Toro Lawn Mower doesn't drive, try these steps: 1. Tighten the by pass valves. 2. Change the belt. 3. Replace the spring. 4. Add hydraulic oil to reservoirs or let it cool down.
General| Start Type | Electric/Recoil |
|---|---|
| Weight | 90 lbs |
| Engine | Briggs & Stratton EXi 163cc w/Just Check & Add |
| Deck Material | Steel |
| Mulching Capability | Yes |
| Bagging Capability | Yes |
| Side Discharge Capability | Yes |
| Engine Type | Gas |
| Cutting Width | 22 inches |
| Drive System | Rear-wheel drive |
| Fuel Capacity | 0.5 gallons |
| Cutting Height | 1.5-4 inches |
| Fuel Tank Capacity | 0.5 gallons |
| Starter Type | Recoil |
To Next Page
