What to do if my Toro Lawn Mower won't drive?
If your Toro Lawn Mower isn't driving, check if the bypass valves are not closed tight and tighten them. Also, the pump belt could be worn, loose, or broken, or off a pulley, in which case change the belt. The idler spring might be broken or missing, so replace the spring. The hydraulic-fluid level might be low or too hot, so add hydraulic fluid to reservoirs or let it cool down.
How to troubleshoot uneven cutting height on my Toro 74938 Lawn Mower?
An uneven cutting height on your Toro Lawn Mower could be due to several factors. The blade(s) might not be sharp, so sharpen them. Alternatively, the cutting blade(s) could be bent, so install new cutting blade(s). The mower deck might not be level, so level the mower deck from side-to-side and front-to-rear. The underside of the mower could be dirty, so clean it. Also, the tire pressure might not be correct, so adjust it.
Why aren't the blades rotating on my Toro 74938?
If the blades on your Toro Lawn Mower aren't rotating, check for a damaged, worn, loose, or broken mower deck belt and install a new deck belt if needed. If the mower deck belt is off the pulley, install it back on the deck pulley and check the idler pulley, idler arm, and spring for correct position and function. Inspect the pump drive belt for wear, looseness, or breakage; check the belt tension or install a new belt. Replace the idler spring if it is broken or missing.
Why won't my Toro 74938 Lawn Mower drive?
If your Toro lawn mower isn't driving, check if the by pass valves are not closed tight and tighten them. Also, inspect the pump belt for wear, looseness, or breakage and change the belt if needed. Ensure the pump belt is on a pulley. Replace any broken or missing idler spring. Lastly, check the hydraulic oil level and add hydraulic oil to reservoirs or let it cool down if it's too hot.
How to fix a starter that won't crank on my Toro Lawn Mower?
If the starter on your Toro Lawn Mower won't crank, check these items: * Ensure the blade-control switch is disengaged. * Engage the parking brake. * Move the motion-control levers to the NEUTRAL-LOCK position. * Make sure you are sitting in the operator’s seat. * Charge the battery if it's dead. * Check the electrical connections for good contact. * Replace the fuse if it's blown.
Why is there abnormal vibration in my Toro Lawn Mower?
If your Toro Lawn Mower experiences abnormal vibration, try the following: Install new cutting blade(s). Tighten the blade mounting bolt. Tighten the engine mounting bolts. Tighten the appropriate pulley. If the issue continues, contact an Authorized Service Dealer.
What to do if my Toro 74938 Lawn Mower overheats?
If your Toro Lawn Mower engine is overheating, it could be due to a few reasons. First, the engine load might be excessive, so try reducing the ground speed. Another cause could be a low oil level in the crankcase, so add oil. Finally, check the cooling fins and air passages above the engine for any obstructions and remove them.
Why Toro 74938 pulls left or right?
If your Toro Lawn Mower pulls to the left or right (with levers fully forward), it could be due to the tracking needing adjustment, so adjust the tracking. Alternatively, the tire pressure in the drive tires might not be correct, so adjust it.
What to do if my Toro Lawn Mower blades do not rotate?
If the blades on your Toro Lawn Mower do not rotate, try these solutions: * Install a new deck belt. * Install the mower deck pulley and check the idler pulley, idler arm, and spring for correct position and function. * Check the belt tension or install a new belt. * Replace the spring.
What to do if my Toro 74938 is resulting in uneven cutting height?
If mowing with your Toro Lawn Mower results in an uneven cutting height, try the following: * Sharpen the blade(s). * Install new cutting blade(s). * Level the mower deck from side-to-side and front-to-rear. * Clean the underside of the mower. * Adjust the tire pressure.
General| Start Type | Electric/Recoil |
|---|---|
| Weight | 90 lbs |
| Engine | Briggs & Stratton EXi 163cc w/Just Check & Add |
| Deck Material | Steel |
| Mulching Capability | Yes |
| Bagging Capability | Yes |
| Side Discharge Capability | Yes |
| Engine Type | Gas |
| Cutting Width | 22 inches |
| Drive System | Rear-wheel drive |
| Fuel Capacity | 0.5 gallons |
| Cutting Height | 1.5-4 inches |
| Fuel Tank Capacity | 0.5 gallons |
| Starter Type | Recoil |
To Next Page
