To Next PageTo Next PageHow to fix uneven cutting height on my Toro 78370 Lawn Mower?
Uneven cutting height on your Toro Lawn Mower can be caused by several factors: * Incorrect tire pressure: Set the tire pressure correctly. * The mower not being level: Level the mower from side-to-side and front-to-rear. * A dirty mower underside: Clean the underside of the mower.
Why is my Toro Mower cutting at an uneven height?
An uneven cutting height on your Toro Mower may be due to incorrect tire pressure, the mower not being level, or a dirty mower underside. Set the tire pressure, level the mower from side-to-side and front-to-rear, and clean the underside of the mower.
Why is my Toro 78370 Lawn Mower vibrating abnormally?
Abnormal vibration in your Toro Lawn Mower can stem from several issues. It might be due to a bent or unbalanced cutting blade, which requires a new blade. Alternatively, the blade mounting bolt or engine mounting bolts could be loose, needing tightening. A loose engine pulley, idler pulley, or blade pulley could also be the culprit, so check and tighten them as necessary. If the engine pulley is damaged, contact an Authorized Service Dealer.
What to do if the blades don't rotate on my Toro Lawn Mower?
If the blades on your Toro Lawn Mower aren't rotating, the blade drive belt might be worn, loose, or broken, requiring a replacement. The belt could also be off the pulley, in which case you should reinstall it and check the idler pulley and belt guides for correct positioning. Another possibility is that the PTO belt is worn, loose, or broken, which also necessitates a new PTO belt.
What to do if the PTO belt keeps coming off the pulleys on my Toro 78370?
If the PTO belt on your Toro Lawn Mower keeps coming off the pulleys, several factors could be responsible. The belt tension might be incorrect, so you should adjust it. The blade slope or blade slope in transport could also be incorrect, requiring adjustment. Additionally, the belt might be worn or damaged, necessitating a new belt. If the pulley is damaged, contact an Authorized Service Dealer.
Why is there insufficient transport height on my Toro 78370 Lawn Mower?
Insufficient transport height on your Toro Lawn Mower may be due to improperly adjusted lift arm cams. To resolve this, adjust the lift arm cams.
How to fix abnormal vibration in my Toro Mower?
Abnormal vibration in your Toro Mower can stem from several issues. A blade might be bent or unbalanced, a blade mounting bolt could be loose, or the engine mounting bolts might need tightening. Check for a loose engine pulley, idler pulley, or blade pulley. Install new blades, tighten the blade mounting bolts, tighten the engine mounting bolts, and tighten the appropriate pulley.
What to do if the blades do not rotate on my Toro Mower?
If the blades on your Toro Mower aren't rotating, the blade drive belt could be worn, loose, or broken, or it may have come off the pulley. Alternatively, the PTO belt might be worn, loose, or broken. Install a new blade drive belt, install the blade drive belt and check idler pulley and belt guides for correct position, or install a new PTO belt.
How to increase the transport height on my Toro Mower?
If you have insufficient transport height on your Toro Mower, the lift arm cams may be improperly adjusted. Adjust the lift arm cams.
General| Model | 78370 |
|---|---|
| Deck Material | Steel |
| Type | Walk-Behind Lawn Mower |
| Power Source | Gas |
| Cutting Width | 22 inches |
| Deck Size | 22 inches |
| Drive Type | Self-propelled |
| Drive System | Rear Wheel Drive |
| Oil Capacity | 20 oz |
Explains the location and importance of safety decals found on the mower.
Steps to prepare the mower and tractor before attachment, including discharge chute installation.
Detailed procedure for attaching the mower deck to the tractor using the Attach-A-Matic system.
Guides on how to engage and disengage the PTO for powering the mower's clutch.
Information on inspecting, removing, and replacing the mower blade for optimal cutting quality.
Step-by-step guide on how to sharpen the mower blade and check its balance.
Procedure for correctly installing the mower blade onto the spindle after sharpening or replacement.
