What to do if my Toshiba Label Maker displays 'HEAD OPEN' during feed or printing?
If the print head block is open while attempting to feed or print on your Toshiba Label Maker, close the print head block and then press the [RESTART] key.
How to resolve a HEAD OPEN error on my Toshiba Label Maker?
If the print head block is open in Online Mode on your Toshiba Label Maker, close the print head block and then press the [RESTART] key.
Why does the cutter on my Toshiba Label Maker not cut?
If your Toshiba Label Maker's cutter is not working, it might be because: * The Cutter Cover is not attached properly. Attach the Cutter Cover correctly. * The media is jammed in the Cutter. Remove the jammed paper. * The Cutter Blade is dirty. Clean the Cutter Blade.
Why is the printed image blurred on my Toshiba B-852-TS22-QQ-R?
If the printed image from your Toshiba Label Maker is blurred, it could be because: * The ribbon and media are not matched. Select an appropriate ribbon for the media type being used. * The Print Head is not clean. Clean the print head using the supplied Print Head Cleaner.
Why is my Toshiba Label Maker printing blank labels?
If your Toshiba Label Maker is not printing anything on the media, it could be due to several reasons: * The media is not loaded properly, load the media correctly. * The ribbon is not loaded properly, ensure the ribbon is correctly installed. * The print head is not installed properly, properly install the print head and close the print head block. * The ribbon and media are not matched, select an appropriate ribbon for the media type being used.
What to do if my Toshiba B-852-TS22-QQ-R Label Maker shows a RIBBON ERROR?
If your Toshiba Label Maker displays 'RIBBON ERROR', it could be due to: * The ribbon is not fed properly. Remove the ribbon, check its status, and replace it if necessary. If the problem persists, turn off the printer and contact an authorized service representative. * The ribbon has run out. Load a new ribbon and then press the [RESTART] key.
How to fix a COMMS ERROR on my Toshiba B-852-TS22-QQ-R Label Maker?
If your Toshiba Label Maker shows a 'COMMS ERROR', ensure the interface cable is firmly connected to the computer and that the computer is turned on. This error indicates a communication problem between the label maker and the computer.
General| Brand | Toshiba |
|---|---|
| Model | B-852-TS22-QQ-R |
| Category | Label Maker |
| Language | English |
Explains the meaning of safety symbols used in the manual.
Overview of the manual's purpose and scope for the printer.
Details the key features and capabilities of the B-852 printer.
Instructions for safely unpacking the printer and checking for damage.
Lists and illustrates the standard accessories included with the printer.
Identifies and illustrates the various parts and components of the printer.
Describes optional modules and add-ons available for the printer.
Provides essential precautions and steps for installing the printer.
Guides on assembling the supply holder frame for media loading.
Details on how to safely connect the printer to a power source.
Step-by-step instructions for loading various types of media correctly.
Explains how to adjust feed gap and black mark sensors for accurate printing.
Procedure for installing the ribbon correctly for thermal transfer printing.
Describes methods for connecting the printer to a host computer.
Safe procedures for powering the printer on and off.
Guide to configuring printer parameters for optimal operation.
Instructions for installing printer drivers on Windows operating systems.
How to perform a print test to verify setup and operation.
Steps for fine-tuning print position, tone, and motor torque.
Procedure for setting sensor thresholds for accurate media detection.
Description of the printer's operation panel, LEDs, and keys.
Details on printer states, error handling, and resuming printing.
Procedure for clearing print data and returning the printer to an idle state.
Instructions for cleaning the print head, platen, and sensors.
Guidance on cleaning the printer's exterior covers and panels.
Steps for cleaning the optional cutter module, with safety warnings.
Lists common error messages, their causes, and solutions.
Addresses common issues like printer not turning on or media not feeding.
Detailed procedure for safely removing jammed media from the printer.
Details the types, sizes, and shapes of media available for the printer.
Explains the movable range of the transmissive sensor for gap detection.
Describes the reflective sensor's range for black mark detection.
Illustrates the relationship between media width and effective print range.
Specifications and recommendations for ribbon types and usage.
Guidance on matching media types with suitable ribbon types.
Best practices for storing and handling media and ribbons to ensure quality.
Details the Centronics interface mode, signals, and data codes.
Describes the USB interface standard, transfer types, and connector.
Information on the LAN interface standard, ports, and LED status indicators.
Specifications for the optional RS-232C serial interface.
Details the wireless LAN module's standard, protocols, and security.
Specifications for the optional Expansion I/O interface and its circuits.
To Next Page
