© 2003 - 2008 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO350/352/353/450/452/453
ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 11
2
CC80 Finisher related
service call
Front alignment motor abnormality: Front alignment
motor is not rotating or front aligning plate is not
moving normally. [MJ-1022]
P. 5 - 8 5
Rear alignment motor abnormality: The rear align-
ment motor is not rotating or the rear alignment
plate is not moving normally. [MJ-1101]
CC90 Upper stack tray lift motor abnormality: The upper
stack tray lift motor is not rotating or the upper stack
tray is not moving normally. [MJ-1022]
P. 5 - 8 6
CCA0 Lower stack tray lift motor abnormality: The lower
stack tray lift motor is not rotating or the lower stack
tray is not moving normally. [MJ-1022]
P. 5 - 8 7
CCB0 Rear jogging motor abnormality: The rear jogging
motor is not rotating or the rear jogging plate is not
moving normally. [MJ-1022]
P. 5 - 8 7
CCD0 Stack ejection motor abnormality: Stack ejection
motor or stack ejection roller is not rotating nor-
mally. [MJ-1023/1024]
P. 5 - 8 8
CCE0 Paper trailing edge assist motor abnormality: Paper
trailing edge assist motor is not rotating or paper
trailing edge assist is not moving normally. [MJ-
1023/1024]
P. 5 - 8 8
CCF0 Gear changing motor abnormality: Gear changing
motor is not rotating normally. [MJ-1023/1024]
P. 5 - 8 8
CDE0 Paddle motor abnormality: The paddle motor is not
rotating or the paddle is not rotating normally. [MJ-
1101]
P. 5 - 8 9
CDF0 Offset tray related ser-
vice call
Initialization error of the offset tray: The home posi-
tion of the separator cannot be detected when the
power is turned ON.
P. 5 - 9 1
CE00 Finisher related ser-
vice call
Communication error between finisher unit and
puncher unit: Communication error between fin-
isher controller PC board and punch controller PC
board [MJ-1023/1024 (when MJ-6004 is installed)]
[MJ-1101 (when MJ-6101 is installed)]
P. 5 - 8 9
CE50 Image control related
service call
Temperature/humidity sensor abnormality: The out-
put value of this sensor is out of a specified range.
P. 5-108
CF10 Finisher related ser-
vice call
Undefined error code processing: If the engine of
the equipment judges that a code (command) other
than the defined error codes is sent from the fin-
isher, it regards this as a CF10 error.
[MJ-1022/1023/1024]
Communication module SRAM writing failure.
[MJ-1101]
P. 5 - 9 0
F070 Communication
related service call
Communication error between System-CPU and
Engine-CPU
P. 5 - 6 9
F090 Other service call SRAM abnormality on the SYS board P. 5-91
F091 NVRAM abnormality on the SYS board P. 5-92
F092 SRAM and NVRAM abnormality on the SYS board P. 5-92
F100 HDD format error: HDD cannot be initialized nor-
mally.
P. 5 - 9 2
F101 HDD unmounted: Connection of HDD cannot be
detected.
P. 5 - 9 2
F102 HDD start error: HDD cannot become ‘Ready’ state. P. 5-92
F103 HDD transfer time-out: Reading/writing cannot be
performed in the specified period of time.
P. 5 - 9 2
Error code Classification Contents Troubleshooting
07/06
To Next Page
Loading...
