Toshiba HWS-1403XWHT6-E Quick Reference

43 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

1

st

Draft: 22/10/10

AIR TO WATER HEAT PUMP

Series 3

FILE NO : A10-002P

Quick Reference

Table of Contents

Other manuals for Toshiba HWS-1403XWHT6-E

Owner's Manual58 pages

Service Manual212 pages

Data Book179 pages

Installation Manual48 pages

Questions and Answers:

C
Carolyn HaleyAug 19, 2025
Why is my Toshiba HWS-1403XWHT6-E Heat Pump not heating or cooling properly?
- A
  Anna RiveraAug 19, 2025
  There are several reasons why your Toshiba Heat Pump might not be heating or cooling effectively. It could be due to an incorrect remote controller setting, so check your operation and temperature settings. An incorrect function code setting could also be the cause; verify the function code setting using the function code table. Other potential issues include a disconnected backup heater (check the heater and bimetal thermostat), insufficient capacity (check the equipment selection), or a sensor defect (ensure the temperature sensor is correctly positioned).
R
Russell BeckAug 21, 2025
Why is my Toshiba HWS-1403XWHT6-E not cooling or heating?
- S
  Seth ParkerAug 21, 2025
  Your Toshiba Heat Pump might not be cooling or heating because a scheduled operation is set. Please check whether scheduled operation is set. Also, check the remote controller to see if night setback operation is enabled. If the air to water heat pump is operating in Auto mode, the target value is set automatically according to the outdoor unit temperature. Note that the Auto mode can be adjusted, but you should contact the installation company for assistance.
J
Julia MitchellAug 23, 2025
Why is nothing displayed on my Toshiba Heat Pump remote controller?
- R
  Ryan ChapmanAug 25, 2025
  If nothing is displayed on your Toshiba Heat Pump remote controller, the issue could be that power is not being supplied. Check the power supply wiring. Alternatively, there might be an incorrect setting; check the DIP switch setting on the Hydro Unit board and compare it with the function code table.
C
Caroline ParkerAug 26, 2025
What causes a Toshiba HWS-1403XWHT6-E Heat Pump E03 communication error?
- R
  Rebecca CamposAug 26, 2025
  If you're experiencing a regular communication error E03 between the hydro unit and the remote controller of your Toshiba Heat Pump, check the remote control connection. Also, check the remote control for any defects.
P
peter19Aug 27, 2025
What to do if my Toshiba Heat Pump is not supplying hot water?
- K
  karenbrownAug 28, 2025
  If your Toshiba Heat Pump isn't supplying hot water, first check if the main water supply cock is closed and ensure the valves are open. Also, consider whether you are using too much hot water; if you use hot water exceeding the storage capacity, water at a temperature lower than the set hot water temperature will be supplied.
C
Cynthia CarneyAug 29, 2025
How to fix a Toshiba HWS-1403XWHT6-E remote controller with no display?
- S
  Steven PattersonAug 29, 2025
  If nothing is displayed on your Toshiba Heat Pump remote controller, check whether power is supplied to the remote. Ensure that the circuit breaker switch is turned on.
D
Dr. Spencer SpencerAug 31, 2025
How to fix a Toshiba HWS-1403XWHT6-E remote controller when nothing is displayed?
- D
  Debra HarrisSep 1, 2025
  If nothing is displayed on your Toshiba Heat Pump remote controller, there are a couple of things to check. First, ensure that power is being supplied to the remote controller by checking the power supply wiring. Also, verify the DIP switch setting on the Hydro Unit board and compare it with the function code table to ensure it is set correctly.
A
Alexis Phelps MDSep 2, 2025
How to troubleshoot regular communication errors between the hydro unit and remote controller of my Toshiba Heat Pump?
- J
  Jesse HarrisonSep 2, 2025
  To troubleshoot communication errors between the hydro unit and the remote controller, check the remote control connection. Also, there may be a defect in the remote control.
B
Betty TuckerSep 5, 2025
What causes regular communication errors between the hydro unit and outdoor unit of a Toshiba HWS-1403XWHT6-E Heat Pump?
- J
  Jessica HaleySep 5, 2025
  To address communication errors between the hydro unit and outdoor unit, check the serial circuit. Also, look for miswiring of the crossover between the water heat exchanger and the outdoor unit.
E
ericjordanSep 7, 2025
What to do if hot water leaks from the Toshiba HWS-1403XWHT6-E pressure relief valve?
- K
  Kenneth SweeneySep 7, 2025
  If hot water is leaking from the pressure relief valve of your Toshiba Heat Pump, it could be due to excessive hydraulic pressure. Set the hydraulic pressure considering the pipe height, and replenish water until the manometer shows a value of set hydraulic pressure or more. Another cause might be insufficient capacity of the expansion tank; check its capacity compared to the total water amount, and install another expansion tank if needed. Finally, the expansion tank might have failed, so check the air pressure.

Toshiba HWS-1403XWHT6-E Specifications

General

Brand	Toshiba
Model	HWS-1403XWHT6-E
Category	Heat Pump
Language	English

Related product manuals

Toshiba HWS-1403XWHT9-E

Toshiba HWS-1403XWHM3-E

Toshiba HWS-1402XWHT9-E

Toshiba HWS-1103H8-E

Toshiba HWS-1603H8-E

Preview: Toshiba HWS-803H-E

Toshiba HWS-803H-E

Preview: Toshiba HWS-805H-E

Toshiba HWS-805H-E

Preview: Toshiba HWS-P805HR-E

Toshiba HWS-P805HR-E

Toshiba HWS-G2601CNMR-E

Preview: Toshiba HWS-G1901CNMR-E

Toshiba HWS-G1901CNMR-E

Preview: Toshiba HWS-804XWHM3 series

Toshiba HWS-804XWHM3 series

Preview: Toshiba ESTIA HWS-802XWHM3-E

Toshiba ESTIA HWS-802XWHM3-E