Toshiba RAS-M10U2KCVG-SG1 x5 - Page 56

Important instruction
To all installers
Please be remined that all air conditioners installed at HDB flats ar
subjected to a current restriction of 11A or 8.5A.
It is the installer’s responsibility to have to current release control set
correctly for the type of HDB flat which the IMS unit is installed
The setting method is the following.
For details refer also to the service manual.
Turn on the circuit breaker
Push SW801 for
5 sec or more
Push SW801 for
5 sec or more
Push SW801
8 times
Push SW801
8 times
Push SW802
1 time
Push SW802
1 time
Push SW802 for
5 sec or more
Push SW802 for
5 sec or more
Push SW801 and SW802
for 5 sec or more
Push SW801
2 times
Push SW802
1 time
Push SW802 for
5 sec or more
Push SW801 and SW802
for 5 sec or more
D800 D801 D802 D803 D804 D805
    
D800 D801 D802 D803 D804 D805
    
D800 D801 D802 D803 D804 D805
   
D800 D801 D802 D803 D804 D805
   
D800 D801 D802 D803 D804 D805

 
D800 D801 D802 D803 D804 D805

 
D800 D801 D802 D803 D804 D805


D800 D801 D802 D803 D804 D805

 
D800 D801 D802 D803 D804 D805


D800 D801 D802 D803 D804 D805

 
D800 D801 D802 D803 D804 D805
 
D800 D801 D802 D803 D804 D805

D800 D801 D802 D803 D804 D805

D800 D801 D802 D803 D804 D805
    
D800 D801 D802 D803 D804 D805
    
<Cancellation method of Power Save setting >
Initial status
:
ON

:
OFF
:
ON

:
OFF
:
ON

:
OFF
:
Slow Flashing (1 time/sec)
:
ON

:
OFF
:
Slow Flashing (1 time/sec)
:
ON

:
OFF
:
Rapid Flashing (5 times/sec)
:
ON

:
OFF
:
Rapid Flashing (5 times/sec)
:
ON

:
OFF
:
Rapid Flashing (5 times/sec)
:
ON

:
OFF
:
Rapid Flashing (5 times/sec)
:
ON

:
OFF
:
Slow Flashing (1 time/sec)
:
ON

:
OFF
:
Slow Flashing (1 time/sec)
Initial status
Setting mode of various functions
Setting mode of various functions
Power Save setting mode(Limit/No limit).
Power Save setting mode(Limit/No limit).
Power Save setting change (No limit → Limit)
Power Save setting change (Limit → No limit)
Power Save setting completion
Power Save setting completion
Current Limit setting mode(11A/8.5A)
Current Limit setting change (11A → 8.5A)
Current Limit setting completion
Function setting completion (return to the initial status)
Function setting completion (return to the initial status)
D805 represents to the limit/No limit.
D805 
:
No limit,
:
Limit (Factory setting
:
No limit)
:
ON

:
OFF
:
Rapid Flashing (5 times/sec)
D805 represents to the 11A/8.5A.
D805

:
11A,
:
8.5A (Factory setting : 11A)
*Go to 1 in the case of 11A setting
1
D805 represents to the limit/No limit.
D805 
:
No limit,
:
Limit (Factory setting
:
No limit)
12-2-8. Grounding
This air conditioner must be grounded without fail.
•
•
Grounding is necessary not only to safeguard against the possibility
of receiving an electric shock but also to absorb both static, which is
generated by high frequencies and held in the surface of the outdoor unit,
and noise since the air conditioner incorporates a frequency conversion
device (called an inverter) in the outdoor unit.
If the air conditioner is not grounded, users may receive an electric shock
if they touch the surface of the outdoor unit and that unit is charged with
static.
Notice
• If an unknown point generated on the way of the operation, push and hold
SW801 and SW802 for 5 seconds or more simultaneously.
You can return to the initial status.
:
ON

:
OFF
:
Rapid Flashing (5 times/sec)
:
ON

:
OFF
:
Slow Flashing (1 time/sec)
:
ON

:
OFF
:
ON

:
OFF
- 56 -