What to do if my Toshiba UPS is overheating?
If your Toshiba UPS is overheating, ensure that the unit's fans and vent holes are not blocked. Also, verify that the surrounding ambient temperature is not above 40 degrees Celsius. If the problem persists after checking these conditions, call service.
What to do if my Toshiba UPS is on battery?
If your Toshiba UPS is operating on battery power, it's crucial to save your data immediately and perform a controlled shutdown of your systems.
How to fix output overload on Toshiba UPS?
If your Toshiba UPS is experiencing an output overload, try shutting off the least important equipment connected to it. If this resolves the issue, the UPS will switch from bypass back to normal operation.
How to resolve site wiring fault on Toshiba UPS?
If your Toshiba UPS detects a site wiring fault due to voltage between neutral and ground, rotate the UPS mains connector polarity. If the UPS is installed to the mains supply without ground, refer to page 15 on how to disable the site wiring alarm.
What to do during a battery test on a Toshiba UPS?
When your Toshiba UPS is running a battery test, no action is needed. The UPS will return to normal operation automatically once the battery test is successfully completed.
What to do if Toshiba UPS shows a bus fault?
If your Toshiba UPS is showing a bus fault due to high internal DC bus voltage, turn off protected loads, turn off the UPS, and call service.
What to do if my Toshiba UPS is overcharging?
If your Toshiba UPS indicates an over-charge, which means the batteries are overcharged, turn off protected loads, turn off the UPS, and call service.
General| Topology | Line Interactive |
|---|---|
| Power Factor | 0.6 |
| Capacity | 1000VA/600W |
| Frequency | 50/60Hz |
| Battery Type | Sealed Lead Acid Maintenance Free |
| Communication Interface | USB |
Defines limitations and restrictions on product usage and warranty coverage.
Specifies requirements and qualifications for personnel handling the equipment.
Outlines the manual's objective, providing information on safe installation and operation of the UPS product.
Provides contact details and operating hours for technical and sales support for UPS products.
Explains safety alert symbols and signal words (DANGER, WARNING, CAUTION) used in the manual.
Details essential practices for safe installation, maintenance, and operation of the UPS and its batteries.
Illustrates and explains various warning symbols found on the UPS, indicating potential hazards.
Declares compliance with EMC standards for residential area installation and provides measures to avoid interference.
Lists the standards and directives the CE-marked units comply with, including safety and EMC regulations.
Provides an overview of the manual's content, covering UPS functions, operation, and installation procedures.
Explains the double conversion on-line UPS operation, including power flow and battery charging.
Details factors for planning a UPS system and available expansion options like external battery cabinets.
Provides vital safety information for handling the UPS unit during storage and transportation.
Explains how to install the UPS safely, highlighting high voltage hazards and user-permissible operations.
Guides on inspecting the UPS for shipping damage and unpacking procedures.
Provides recommendations for storing the UPS and maintaining battery charge during non-use.
Advises on proper disposal of UPS components and batteries, emphasizing environmental regulations.
Lists essential precautions to take before and during UPS installation to ensure safety and prevent damage.
Details guidelines for routing conductors and establishing proper grounding for the UPS system.
Outlines critical precautions to follow during UPS operation to prevent hazards and ensure proper function.
Specifies environmental conditions for UPS installation, including ventilation and temperature, for safety and performance.
Illustrates and labels rear panel connections for 1000VA and 1500VA tower models.
Illustrates and labels rear panel connections for the 2000VA tower model.
Illustrates and labels rear panel connections for the 3000VA tower model.
Illustrates and labels rear panel connections for 1000VA and 1500VA rackmount models.
Illustrates and labels rear panel connections for the 2000VA rackmount model.
Illustrates and labels rear panel connections for the 3000VA rackmount model.
Provides instructions for connecting the UPS to power mains and output loads, including battery charging.
Details the procedure for connecting external battery cabinets to the UPS for extended backup time.
Describes RS232 and USB ports for computer communication and optional interface slots.
Explains the Emergency Power Off (EPO) port and its function for immediate UPS shutdown.
Describes the function and connection of the network transient protector on the UPS rear panel.
Provides step-by-step instructions for powering the UPS on and off, including load management.
Explains the function of each button on the UPS front panel for operation and navigation.
Details UPS status indicators (LEDs) and LCD screen functions for monitoring and alerts.
Guides users on understanding and responding to various messages and audible alarms displayed by the UPS.
Offers a table to diagnose and resolve common UPS issues based on LCD display and audible alarms.
Provides the steps to disable the cold start function and how it is re-enabled.
Covers routine maintenance, environmental factors, and battery replacement considerations for UPS reliability.
Provides a step-by-step tutorial for safely replacing the UPS batteries.
Lists detailed technical specifications for 120V models, including power ratings, input/output parameters, and efficiency.
Lists detailed technical specifications for 230V models, including power ratings, input/output parameters, and efficiency.
Details environmental operating conditions and compliance standards for the UPS units.
Specifies output power details, connection types, battery configuration, and dimensions for 120V tower models.
Specifies output power details, connection types, battery configuration, and dimensions for 120V rackmount models.
Specifies output power details, connection types, battery configuration, and dimensions for 230V tower models.
Specifies output power details, connection types, battery configuration, and dimensions for 230V rackmount models.
Lists the available communication ports such as RS232, USB, and monitoring card slots.
Provides physical dimensions and weight for both tower and rackmount UPS models.
Details the standard warranty period for the UPS and its batteries.
To Next Page
