EasyManuals Logo

Toshiba Tecra A11 User Manual

Toshiba Tecra A11
238 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #105 background imageLoading...
Page #105 background image
User’s Manual 4-4
Operating Basics
How to Swipe your Finger
Using the following steps when swiping fingers for fingerprint registration or
authentication will help to minimize authentication failures:
Align the first joint of the finger to the center of the sensor. Lightly touch the
sensor and swipe finger levelly towards you until the sensor surface
becomes visible. In performing this process, you should also take care to
ensure that the center of your fingerprint is on the sensor.
The following illustrations show the recommended way to swipe your finger
over the fingerprint sensor.
Figure 4-3 Swipe the finger
Points to note about the Fingerprint Sensor
Please be aware of the following considerations when using the fingerprint
sensor. A failure to follow these guidelines might result in damage to the
sensor, sensor failure, fingerprint recognition problems or a lower
fingerprint recognition success rate.
Do not scratch or poke the sensor with your nails or any hard or sharp
objects.
Do not press the sensor strongly.
Do not touch the sensor with a wet finger or any wet objects - keep the
sensor surface dry and free from water vapor.
Do not touch the sensor with a soiled or dirty finger as minute foreign
particles of dust and dirt may scratch it.
1. Sensor
1
1
Avoid swiping with your finger stiff or pressed too hard onto the sensor,
and take care to ensure that the center of the fingerprint is touching the
sensor before swiping. Either of these conditions may cause fingerprint
reading to fail.
Check the center of the fingerprint whorl before swiping and then
ensure this is swiped along the center line of the sensor.
There is a possibility of authentication failures if the finger is swiped too
quickly or too slowly - follow any on-screen instructions to adjust the
speed used during the swipe process.

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Toshiba Tecra A11 and is the answer not in the manual?

Toshiba Tecra A11 Specifications

General IconGeneral
Bus typeDMI
SteppingC2
Tjunction105 °C
Processor cache4 MB
Processor cores2
Processor modeli7-620M
System bus rate2.5 GT/s
Processor familyIntel® Core™ i7
Processor seriesIntel Core i7-600 Mobile Series
Processor socketBGA 1288
Processor threads4
Processor codenameArrandale
Processing Die size81 mm²
Processor frequency2.66 GHz
Processor cache typeSmart Cache
Processor lithography32 nm
Processor manufacturerIntel
Processor front side bus1066 MHz
PCI Express slots version2.0
Processor boost frequency3.33 GHz
Processor operating modes64-bit
ECC supported by processorNo
PCI Express configurations1x16
Thermal Design Power (TDP)35 W
CPU multiplier (bus/core ratio)20
Maximum number of PCI Express lanes16
Number of Processing Die Transistors382 M
HDD speed7200 RPM
HDD interfaceSATA
Optical drive typeDVD Super Multi DL
Total storage capacity320 GB
Number of HDDs installed1
LED backlightYes
Display diagonal15.6 \
Display resolution1600 x 900 pixels
Native aspect ratio16:9
Internal memory4 GB
Internal memory typeDDR3-SDRAM
Maximum internal memory8 GB
Memory layout (slots x size)2 x 2 GB
TypePC
Wireless technology802.11a/g/n
CD-R write speed24 x
CD-RW write speed4 x
Bluetooth version2.1+EDR
Networking features1Gbit
Trial softwareOffice
Operating system installedWindows 7 Professional
Battery life (max)4 h
Charging port typeDC-in jack
Serial ports quantity0
USB 2.0 ports quantity3
Cable lock slot typeKensington
Pointing deviceTouchpad
Discrete graphics card modelGMA QM57
On-board graphics card modelIntel® HD Graphics
On-board graphics card base frequency500 MHz
On-board graphics card dynamic frequency (max)766 MHz
Processor codeSLBPE
Processor ARK ID43560
Processor package sizerPGA 37.5x 37.5, BGA 34x28 mm
Graphics & IMC lithography45 nm
Supported instruction setsSSE4.1/4.2
Intel® Turbo Boost Technology1.0
Physical Address Extension (PAE)36 bit
Weight and Dimensions IconWeight and Dimensions
Depth250.5 mm
Width374 mm
Weight2800 g
Height (rear)37.6 mm
Height (front)33.4 mm

Related product manuals