Toto NEOREST 600 - User Manual

NEOREST 600 Installation Instructions
2005.2.25 D06698-4
l Read and follow all of the instructions before installing the NEOREST.
Safety Instructions
Always follow the safety precautions/warnings when
using and installing the WASHLET.
Improper use of this product may result in death or serious injury.WARNING:
Improper use of this product may result in injury or property damage.CAUTION:
This symbol indicates a prohibited use of the product.
This symbol is used to indicate a required step in the use of this product.
WARNING:
Do not use this product in wet or damp
places, such as a shower or bathtub area.
(This may cause fire or electrical shock.)
Prohibited
Use of This
Product:
Connect to a proper water source to avoid
the risk of skin irritation.
This product should be used with 120V
electrical voltage only to avoid the risk of fire
of electrical shock.
Do not use a damaged plug or cord or insert
into a faulty electrical outlet, as this may
result in fire or electrical shock.
Always plug into a grounded (3 prong) plug to
prevent electrical shock in the case of
malfunction or short circuit.
Always insert the power plug securely into
the wall outlet. Failure to do so may result in
fire or electrical shock.
CAUTION:
To prevent sudden water leakage, do not
remove the water supply filter before
closing the water shutoff valve.
Do not apply force to the flexible connecting
hose or elbow joint as this may result in
water leakage.
When installing the water supply filter, make
sure that it is tightened securely. Improper
installation of the water supply filter may
result in water leakage.
Do not bend or crush the flexible connecting
hose as this may result in water leakage.
Do not lift the Washlet section by grabbing
the seat or lid. The seat or lid may detach
and drop or damage the Neorest.
Always follow the installation instructions
when installing the product. Improper
installation may result in water leakage,
electrical shock or fire.
Before Installation
1. Do not apply power or supply water to the unit until the
installation process is complete.
2. Do not grasp the toilet bowl connecting hose when mounting
the W
ashlet main unit onto the toilet bowl.
3. The power voltage is 120V/60Hz. The rated energy consumption
is 1288W. Use wiring and electrical outlet appropriate for this level
of power.
4. The power cord is 3 feet (1m) in length. The electrical outlet
should be located on the wall, within reach of the power plug.
5. Use a minimum water supply pressure of 10 PSI (0.07 Mpa)
flowing.
6. The water temperature range should be 0 ~ 35°C (32~95°F).
7. Only use the flexible connecting hose provided in this kit.
Flush lever
Seat sensor
Wand
Heated toilet seat
Toilet bowl
Motion detection sensor
Main unit
Main unit controls
Remote control receiver
Remote controller
Motion detection sensor
Lid
Main unit
display panel
Washlet water
shutoff valve
Water shutoff valve
(includes filter)
Power plug
Flexible connecting hose
Parts Identification Features
Package
36" x 20" x 12"
(920(L) x 506(W) x 300(D)mm)
Washlet Main Unit
Main Unit Installation
Hardware:
Remote Controller Parts:
Remote Controller
Remote
Controller Hanger
2 x AA Batteries
3 Screws
3 Anchor Bolts
Wrench
Anti-theft
remote
control
mounting
blocks
Leave with
Owner after
installation.
Hose housing
cover with
screw
Flexible connecting hose
Length: 15" (380mm)
Equipped with packing
washer and O-ring.
l Instructions Manual
l Installation Instructions
l "How-To" Guide
l Warranty Card
l Flush Label
l Hook
(Instructions included)

Summary

Safety Instructions

General Safety Precautions and Symbols

Explains general warnings, cautions, and symbols for safe product use.

Before Installation Requirements

Installation Prerequisites

Lists essential requirements and conditions before starting the installation process.

Main Unit Installation

Mounting the Washlet Main Unit

Detailed steps for securely mounting the Washlet main unit onto the toilet bowl fixture.

Connecting Water Supply Hoses

Hose Fitting and Connection Procedure

Guide to properly fitting and connecting the water supply and connecting hoses.

Remote Controller Installation

Battery Insertion and Hanger Mounting

Instructions for installing batteries and attaching the remote controller hanger to the wall.

Trial Operation - Initial Checks

Initial Setup and Leak Detection

Performing initial checks, turning on water, and verifying for any leaks.

Core Functionality Verification

Testing seat sensor, air deodorizer, warm water wash, and dryer functions.

Trial Operation - Continued Functions

Automated Features Testing

Testing auto flush, remote flush, and seat/lid open/close operations.

Advanced Operation and Drainage

Testing auto open/close lid, draining pipes, and final trial operation steps.

Water Supply Filter Maintenance

Filter Cleaning and Reinstallation

Procedure for cleaning the water supply filter and ensuring proper reinstallation.

Toto NEOREST 600 Specifications

General

Type	One-Piece Toilet
Bowl Height	16.5 inches
Bowl Shape	Elongated
Material	Ceramic
Color	Cotton White
Features	Heated Seat
Power Source	AC120V