Toyota VENZA PT949-08210 User Manual

TOYOTA VENZA 2021 - DASHCAM (Digital Video Recorder)
Preparation
Page 1 of 11 pages
Issue: D 4/14/2021
DIO
Part Number: PT949-08210 (Dash Cam)
PT949-48210 (Y-Harness)
Kit Contents
Item #
Quantity Reqd.
Description
1
1
Dashcam Main Unit
4
1
Window Mounting Plate
5
2
Foam Tape
6
4
Cable Ties
7
1
Quick Start Guide
1
1
Y-Harness
Hardware Bag Contents
Item #
Quantity Reqd.
Description
1
2
3
Additional Items Required For Installation
Item #
Quantity Reqd.
Description
1
2
Conflicts
None
Recommended Tools
Personal & Vehicle
Protection
Notes
Seat protection
Dash protection
Special Tools
Notes
Installation Tools
Notes
Panel Tool
Socket Wrench
With 10mm socket
Torque Wrench
With 10mm socket
Special Chemicals
Notes
VDC approved cleaner
To clean windshield
General Applicability
Applicable to XLE, Limited models
Recommended Sequence of Application
Item #
Accessory
1
Dashcam (PT949-08210)
2
Y-Harness (PT949-48210)
3
*Mandatory
Vehicle Service Parts (may be required for reassembly)
Item #
Quantity Reqd.
Description
1
2
3
Legend
STOP: Damage to the vehicle may occur. Do not
proceed until process has been complied with.
OPERATOR SAFETY: Use caution to avoid risk of
injury.
CAUTION:
A process that must be carefully observed
in order to reduce the risk of damage to the
accessory/vehicle and to ensure a quality installation.
TOOLS & EQUIPMENT:
Used in Figures calls out the
specific tools and equipment recommended for this
process.
REVISION MARK: This mark highlights a change in
installation with respect to previous issue.
SAFETY TORQUE: T
his mark indicates that torque is
related to safety.

Toyota VENZA PT949-08210 Specifications

General

Brand	Toyota
Model	VENZA PT949-08210
Category	Dash Cameras
Language	English

Summary

Installation Preparation

Legend

Explains symbols used throughout the installation procedure for clarity and safety.

Installation Procedure

Protect Vehicle and Disconnect Battery

Ensure vehicle protection and safely disconnect the battery before starting installation.

Apply Vehicle Protection

Apply protective coverings to seats, dash, and center console to prevent damage.

Install Windshield Base Plate

Clean windshield area and securely attach the base plate using the provided template.

Remove Roof Console

Carefully detach the roof console by releasing front and rear clips to access wiring.

Remove the TSS Cover

Rotate mirror down and remove the two-piece mirror cover plate to access TSS cover.

Install the Y-Harness

Connect the Y-harness between the vehicle mirror connector and the dashcam harness.

Reinstall the TSS Cover

Reinstall the TSS cover and mirror cover plate, ensuring all clips are engaged.

Affix Dashcam to Base Plate

Route dashcam pigtail through headliner notch and attach dashcam unit to base plate.

Hook Harness Protector under Headliner

Pull headliner down slightly and hook the harness protector securely under the headliner.

Route/Bundle Wire Harness

Gather and bundle dashcam and Y-harness wires, securing them with wire ties.

Reassemble the Console

Reconnect roof console connectors and reinstall the console, ensuring clips engage.

Reconnect Battery

Reconnect the negative battery cable and tighten to the specified torque value.

Reinstall Battery Cover and Remove Protective Covering

Reinstall the battery service hole cover and remove any vehicle protective coverings.

Final Checks and Verification

Accessory Function Checks

Verify dashcam startup, LED lights, and ensure no continuous beep on vehicle startup.

Vehicle Function Checks

Confirm standard lighting and roof console functions operate correctly after installation.

Vehicle Appearance Check

Visually inspect for any damage, scuffs, or scratches caused during installation.