TP-Link VIGI C320I User Manual (English)

To Next Page

Quick Start Guide

*Images may dier from actual products.

VIGI C330I is used for demonstration in this guide.

Appearance

*Some models do not have the power supply interface. You can check the

detailed specications on the product page at https://www.tp-link.com/.

Power Supply Interface (12V DC)*

RJ45 Ethernet Port (supports PoE)

IR LED

Lens

Package Contents

Network Camera

Waterproof Cable

Attachments

Quick Start Guide

Anchors and Screws

Quick

Start

Guide

•

Make sure your power supply matches your camera.

The camera’s standard power supply is 12V DC* or

PoE (802.3af/at). The power source should meet LPS,

PS2, and other requirements according to IEC

62368-1.

• Make sure that the wall is strong enough to

withstand 4 times the weight of the camera and

mounting bracket.

• If you are uncertain or uncomfortable performing the

installation, consult a qualied electrician.

Safety First:

Installing Waterproof Cable Attachments

Install the waterproof cable attachments for the network

interface when the camera is installed outdoors.

Note: Make sure each part is securely attached and the waterproof

rings are ush to keep out water.

Done! The network interface is now waterproof.

Mount Camera

Fix Nut

Waterproof

Ring

O-ring

Network

Interface

Waterproof

Jacket

1. Route the network cable through the following

components in order: x nut, waterproof ring, and then

the waterproof jacket.

2. Fix the O-ring to the network interface of the camera and

connect the network cables.

3. Attach the network interface with the waterproof jacket,

then twist to lock.

4. Insert the waterproof ring into the waterproof jacket.

Rotate the x nut to secure it to the waterproof jacket.

Mounting Template

Option 1: Wall/Ceiling Mounting

1. Stick the mounting template to the desired mounting place.

Drill 4 screw holes according to the template.

2. Insert the anchors into the holes, use the provided screws to

x the camera’s bracket to the wall or ceiling.

Option 2: Pole Mounting

1. Thread each of the two cable ties through the slits on the

back of the camera’s bracket indicated below.

2. Slip the two cable ties through the pole. Tighten them to

rmly attach the pole.

Need help?

Do you have a question about the TP-Link VIGI C320I and is the answer not in the manual?

TP-Link VIGI C320I Specifications

General

Type	IP security camera
Placement supported	Outdoor
Connectivity technology	Wired
Wide Dynamic Range (WDR)	Yes
Built-in HDD	No
Form factor	Bulb
Mounting type	Ceiling/Wall/Pole
Product color	Black, White
Housing material	Plastic
Protection features	Waterproof
International Protection (IP) code	IP67
Minimum illumination	0.1 lx
Lens diameter	2.8 mm
Number of lenses	1
Maximum aperture number	2.2
Sensor type	CMOS
Optical sensor size	1/3 \
DC output voltage	12
Power source type	DC, PoE
Operating temperature (T-T)	-30 - 60 °C
LED type	IR
Night vision distance	30 m
Total megapixels	2 MP
Maximum resolution	1920 x 1080 pixels
Image quality adjustment	Brightness, Contrast, DNR, Mirror, Saturation, Sharpness
Video compression formats	H.265+, H.264, H.264+, H.265
Noise reduction technology	3D noise reduction
Bluetooth	-
Networking standards	IEEE 802.3af, IEEE 802.3at
Ethernet interface type	Fast Ethernet
Supported network protocols	TCP/IP, UDP, ICMP, HTTP, HTTPS, DHCP, DNS, RTSP, NTP, UPnP UDP, SSL/TLS