How to stop rapid burner cycling in my Trane Furnace?
To address rapid burner cycling in your Trane Furnace: 1. Tighten all electrical connections. 2. Adjust the thermostat heat anticipation for longer cycles (refer to the operation guide). 3. Check for proper air supply across the heat exchanger. 4. Relocate the thermostat (do not mount the thermostat on the unit).
Why is my Trane Furnace not producing enough heat?
If your Trane Furnace is not producing enough heat: 1. Consult the operation guide. 2. Consider if the heated space has been enlarged. Have the heat loss calculated and compare it to the heater output (80% of input). Your gas supplier or installer can provide this information. If the heater is undersized, add additional heaters. 3. Replace the thermostat. 4. Check air movement through the heat exchanger. Check the voltage to the power venter motor, clean the power venter wheel and heat exchanger, and oil the power venter motor. Check filters and replace them if necessary. 5. Adjust dampers accordingly.
What to do if my Trane Furnace is producing too much heat?
If your Trane Furnace is producing too much heat: 1. Replace the thermostat. 2. Check the wiring per the diagrams, check the operation at the valve (look for shorts and correct them, such as staples piercing thermostat wiring), replace the gas valve, and refer to the operation guide.
What to do if my Trane Fan motor has a blown fuse?
If the Trane Fan motor has a blown fuse or an open circuit breaker, replace the fuse or reset the circuit breaker.
What to do if Trane Fan motor does not come up to speed?
If your Trane Fan motor isn't reaching full speed, the motor might be too small for the application, in which case you should replace it with a larger motor. Alternatively, the voltage at the motor terminals might be too low; check the voltage across the AC line and correct it if possible.
How do I fix a Trane Furnace burner that won't turn off?
If the burner on your Trane Furnace won't turn off: 1. Relocate the thermostat away from drafts. 2. Replace the thermostat. 3. Check the wiring diagrams. 4. Check the operation at the valve and look for shorts (such as staples piercing thermostat wiring) and correct them. 5. Replace the gas valve. 6. Refer to the operation guide.
How to fix a noisy flame in my Trane Furnace?
If your Trane Furnace has a noisy flame: 1. Close the air shutter and open all manual gas valves. 2. Reduce pilot gas (refer to the operation guide). 3. Replace the orifice. 4. Reset the manifold pressure (refer to the operation guide), replace the regulator section of the combination gas valve or the complete valve, or check with your local gas supplier for the proper orifice size and replace it (refer to the operation guide).
How to fix yellow tip flame on my Trane Furnace?
To address yellow tipping on the flame of your Trane Furnace (some yellow tipping on propane gas is permissible): 1. Open the air shutters (refer to the operation guide). 2. Clean the main burner ports. 3. Replace the manifold assembly. 4. Check for dust or lint at the air mixer opening and around the air shutter. 5. Clean the combustion air inlet openings in the bottom panel (refer to the installation guide). 6. Clean the draft hood/flue collector.
How to fix delayed ignition on my Trane Furnace?
To resolve a delayed ignition issue with your Trane Furnace: 1. Close the air shutter (refer to the operation guide). 2. Clean the main burner ports. 3. Reset the manifold pressure (refer to the operation guide). 4. Ensure the supply piping is adequately sized (refer to the installation guide). 5. Clean the pilot orifice (refer to the operation guide).
How to get rid of gas odor from my Trane Furnace?
If you smell gas coming from your Trane Furnace: 1. Inspect all gas piping and repair any leaks. 2. Clean the heat exchanger. 3. Address any drafts (refer to the installation instructions). 4. Consult the installation guide. 5. Clean the draft hood or flue collector.
Defines advisory types for safety: Warning, Caution, and Notice.
Details mandatory PPE for safe operation and servicing of equipment.
Safety warning about working with live electrical components before servicing.
Essential instructions for safe gas piping installation and leak testing.
Detailed steps for making safe and correct electrical connections.
Explanation of the unit's gas control system and its sequence of operation.
Emphasizes testing all safety controls before initial operation.
Safety guidelines for performing maintenance tasks on the equipment.
Diagnosing and resolving common issues related to the air blower.
Diagnosing and resolving common problems with electric motors.
Diagnosing and resolving common issues related to the fan assembly.
Diagnosing and resolving common problems with DX cooling coils.
Diagnosing and resolving common problems with chilled water coils.
Pre-operation checklist before powering and gassing the unit.
General| Refrigerant | R-410A |
|---|---|
| Voltage | 208/230V |
| SEER | Up to 18.0 |
| HSPF | Up to 10.0 |
| Phase | 1-Phase |
| Warranty | 10-year limited warranty on compressor |
To Next Page
