45
1. Password required to access field start up group
(++—++)
2. Keypad or Display lock feature: [d/e]
Press (+)(-) to change setting
3. Menu settings password feature: [d/e]
Press (+)(-) to change setting
4. Password duration time: xxx minute
Press (+)(-) to change setting
5. ICS address: xx
Press (+)(-) to change setting
6. Power up start delay time: xxx second
Press (+)(-) to change setting
7. Cooling delta temperature setpoint: xx.x f/c
Press (+)(-) to change setting
8. Leaving water temperature cutout setpoint: xxx.x f/c
Press (+)(-) to change setting
9. Low refrigerant tempeature cutout setpoint: xxx.x f/c
Press (+)(-) to change setting
10. Softload time: xxx minute
Press (+)(-) to change setting
Energy Vlv Soft Unload Control: [ d/e ]
Press (+)(-) to change setting
11. Energy Vlv Soft Unload rate: xxx %/5 second
Press (+)(-) to change setting
12. Under or over voltage protection: [d/e]
Press (+)(-) to change setting
13. Absorber or condenser temperature low relay setpointt: xxx.x f/c
Press (+)(-) to change setting
14. Chilled water control gain: xxx
Press (+)(-) to change setting
15. Chilled water control reset: xxxx
Press (+)(-) to change setting
16. Chilled water control derivative: xxxx
Press (+)(-) to change setting
17. Evaporator time constant: xxx second
Press (+)(-) to change setting
18. LTHX crystallization margin setpoint: xxx.x f/c
Press (+)(-) to change setting
19. Concentration control gain: xxxx
Press (+)(-) to change setting
20. Concentration control reset: xxx
Press (+)(-) to change setting
21. Concentration control derivative: xxxx
Press (+)(-) to change setting
22. Concentration offset generator number 1: xxx.x%
Press (+)(-) to change setting
23. Concentration offset generator number 2: xxx.x%
Press (+)(-) to change setting
24. Generator time constant: xxx second
Press (+)(-) to change setting
25. Solution pump AFD minimum frequency: xx hz
Press (+)(-) to change setting
26. Solution pump AFD maximum frequency: xx hz
Press (+)(-) to change setting
28 EV Maximum Travel Setpoint: xx,xxx Steps
Press (+)(-) to change setting
29. Energy input closed stop: xxx%
Press (+)(-) to change setting
30. Energy input open stop: xxx%
Press (+)(-) to change setting
31. Minimum alternate fuel firing rate: xxx%
Press (+)(-) to change setting
33. Maximum wait for combustion time: xx minute
Press (+)(-) to change setting
34. Heating delta temperature setpoint: xx.x f/c
Press (+)(-) to change setting
35. Hot water control gain: xxxx
Press (+)(-) to change setting
36. Hot water control reset: xxxx
Press (+)(-) to change setting
37. Hot water control derivative: xxxx
Press (+)(-) to change setting
38. Auxiliary heat valve maximum travel: xxxx steps
Press (+)(-) to change setting
39. Auxiliary heat valve closed stop: xxx%
Press (+)(-) to change setting
40. Auxiliary heat valve open stop: xxx%
Press (+)(-) to change setting
41 Purge maximum pumpout rate: xxx min or 24 hours
Press (+)(-) to change setting
42 Absorber Purge Pumpout Interval: xxx minutes
Press (+)(-) to change setting
43 Absorber Pumpout Duration: xxx minutes
Press (+)(-) to change setting
44 Low evaporator flow warning: xx.x gpm/ton
Press (+)(-) to change setting
45. Variable FLow Rate Control: [d/e]
Press (+)(-) to Change Setting
46. Evaporator Flow Rate - High: xxx gpm
Press (+)(-) to Change Setting
47. Evaporator flow rate - Low: xxx gpm
Press (+)(-) to change setting
48. Evaporator Pressure Drop - High: xx.x Ft
Press (+)(-) to change setting
49. Evaporator Pressure Drop - Low: xx.x Ft
Press (+)(-) to change setting
50. Evaporator fluid coefficient: xxx
Press (+)(-) to change setting
51 Absorber or condenser flow rate - High; xxx gpm
Press (+)(-) to change setting
52 Absorber or condenser flow rate - Low: xxx gpm
Press (+)(-) to change setting
53 Absorber or condenser Pressure Drop - Low: xxx Ft
Press (+)(-) to change setting
54 Absorber or condenser Pressure Drop -High: xxx Ft
Press (+)(-) to change setting
Service Settings: Field Start Up
Group (++—++) OVERVIEW
[Shaded is sales order specified]
To Next Page
Loading...
