33
DECLARATION
Les parties/paragraphes suivants des normes harmonisées ont été appliquées. / The following parts/clauses of harmonized
standards have been applied. / Folgende harmonisierten Normen oder Teile / Klauseln hieraus zur Anwendung gelangten. /
Части следните хармонизирани стандарти са приложени. / byly použity následující části/ustanovení harmonizovaných
technických norem / Eventuelt henvisning til de harmoniserede standarder / όροι των εναρμονισμένων με την οδηγία κανονισμών
έχουν εφαρμοσθεί. / Las siguientes normas armonizades, o partes de ellas, fueron aplicadas. / Parts / järgmiste ühtlustatud
standardite kohaldamist. / Seuraavia yhdenmukaistettuja standardeja tai niiden osia/kohti) on sovellettu. / Dijelovi / slijedeći
harmoniziranih standarda su primijenjene. / Alkatrészek követően harmonizált szabványokat alkalmazták. / Sono state applicate
le seguenti parti/clausole di norme armonizzate./ Dalys / šie darnieji standartai nebuvo taikomi. / Parts / šādi saskaņoti standarti
tika piemērots. / Partijiet li ġejjin ġew applikati standards armonizzati. / De volgende onderdelen van geharmoniseerde normen
zijn toegepast / Folgende deler/punkter i harmoniserte standarder har vært anvendt./ Części / następujące zharmonizowane
normy zostały zastosowane. / Foram observadas as/os seguintes partes/parágrafos das normas harmonizadas : /Piese
următoare s-au aplicat standardele armonizate / Были применены следующие части/положения согласованных
стандартов./ Parts nasledujúce harmonizované normy neboli použité. / Deli po usklajenih standardih, so bili uporabljeni. /Att
följande harmoniserande standarder eller delar därav har tillämpats. / Aşağıdaki standartlar uygulanmıştır. / Частини наступні
узгоджені стандарти застосовувалися:
EN 349:1993+A1:2008 Safety of machinery - Minimum gaps to avoid crushing of parts of the human body
EN ISO 12100:2010 Safety of machinery - General principles for design - Risk assessment and risk reduction
EN ISO 13857:2008 Safety of machinery - Safety distances to prevent hazard zones being reached by upper and lower limbs
EN 60034-1:2010 Rotating electrical machines - Part 1: Rating and performance.
EN 60034-7:1993 Rotating electrical machines - Part 7: Classification of types of construction, mounting arrangements and
terminal box position.
EN 60204-1:2006 Safety of machinery - Electrical equipment of machines - Part 1: General requirements.
EN 61000-6-1:2007 Electromagnetic compatibility (EMC) - Part 6-1: Generic standards - Immunity for residential, commercial
and light-industrial environments
EN 61000-6-3:2007/A1:2011 Electromagnetic compatibility (EMC) - Part 6-3: Generic standards - Emission standard for
residential, commercial and light-industrial environments
ISO 1496-2 1996 Series 1 freight container: specification and testing: thermal container
EN 378-1:2008 Refrigerating systems and heat pumps - Safety and environmental requirements - Part 1: Basic requirements,
definitions, classification and selection criteria .
EN 12830:1999 Temperature recorders for the transport, storage and distribution of chilled, frozen, deep-frozen/quick-frozen
food and ice cream. Tests, performance, suitability.
NF EN 13485 2001 Thermometers for measuring the air and product temperature for the transport, storage and distribution of
chilled, frozen, deep-frozen/quick-frozen food and ice cream - Tests, performance, suitability.
NF EN 13486 2001 Temperature recorders and thermometers for the transport, storage and distribution of chilled, frozen,
deep-frozen/quick-frozen food and ice cream - Periodic verification
To Next Page
Loading...
