-13-
ACCESSORIES
Please use only Trend original accessories.
Recommended Cutters
• Ref. 3/83X1/2TC, 3/83DX1/2TC, 3/83DCX1/2TC,
C153X1/2TC, C153DX1/2TC or RT/13X1/2TC
Sub-base Set
• Ref. UNIBASE
• To obtain a perfect accurate close fitting joint, a 30mm
guide bush must be used. The guide bush must
always be fitted concentric with the cutter. This can
be achieved using a Universal Sub-base and 30mm
outside diameter guide bush ref. GB30/A.
30mm Guide Bush
• Ref. GB30/A
Panel Connector Bolts
• Ref. PC/10/M (Pack of 10)
• Ref. PC/50/M (Pack of 50)
• Ref. PC/100/M (Pack of 100)
• Ref. PC/1000/M (Pack of 1000)
Biscuit Jointer for the Router
• Ref. 342X1/2TC
• Ref. C152X1/2TC
5.5mm
10mm
EN
CL
CL
8.5mm
8.5mm
CL
CL
8.5mm
Start Here
Start Here
Cut with laminate down
Cut with laminate up
8.5mm
CL
CL
8.5mm
8.5mm
CL
CL
Engraved lines
Start Here
Start Here
12,7mm
50mm
No.20
PVA
SEALANT
Waterproof
UNIBASE
t
r
e
n
d
3
0
m
m
R
PF
W
Male Male
Female
2 4
1 3
7 5
Female
8
Male
6
Male
45
o
Joint
Male Male
Female
3 5
2 4
8 6
Female
9
Male
7
Male
45
o
Joint
2
3
Female
Male
5
4
Female
Male
PF
40mm
Cut 1
3mm
Cut 2
8mm
Cut 4
Final cut
Cut 3
40mm 28mm
Worktop
PF
30mm 20mm
Worktop
Worktop
G
Joint (35mm Inset)
35mm
Inset
35mm
Inset
90
o
90
o
Joint (35mm Inset)
Cutter
Sub base
Location pin
8.5mm
Worktop
Template
Cutter
Sub baseGuide bush Ø30mm
Location pin
8.5mm
Worktop
Template
Guide bush Ø30mm
Template
PF
PF
Cut 5
5.5mm
10mm
EN
CL
CL
8.5mm
8.5mm
CL
CL
8.5mm
Start Here
Start Here
Cut with laminate down
Cut with laminate up
8.5mm
CL
CL
8.5mm
8.5mm
CL
CL
Engraved lines
Start Here
Start Here
12,7mm
50mm
No.20
PVA
SEALANT
Waterproof
UNIBASE
t
r
e
n
d
3
0
m
m
R
PF
W
Male Male
Female
2 4
1 3
7 5
Female
8
Male
6
Male
45
o
Joint
Male Male
Female
3 5
2 4
8 6
Female
9
Male
7
Male
45
o
Joint
2
3
Female
Male
5
4
Female
Male
PF
40mm
Cut 1
3mm
Cut 2
8mm
Cut 4
Final cut
Cut 3
40mm 28mm
Worktop
PF
30mm 20mm
Worktop
Worktop
G
Joint (35mm Inset)
35mm
Inset
35mm
Inset
90
o
90
o
Joint (35mm Inset)
Cutter
Sub base
Location pin
8.5mm
Worktop
Template
Cutter
Sub baseGuide bush Ø30mm
Location pin
8.5mm
Worktop
Template
Guide bush Ø30mm
Template
PF
PF
Cut 5
5.5mm
10mm
EN
CL
CL
8.5mm
8.5mm
CL
CL
8.5mm
Start Here
Start Here
Cut with laminate down
Cut with laminate up
8.5mm
CL
CL
8.5mm
8.5mm
CL
CL
Engraved lines
Start Here
Start Here
12,7mm
50mm
No.20
PVA
SEALANT
Waterproof
UNIBASE
t
r
e
n
d
3
0
m
m
R
PF
W
Male Male
Female
2 4
1 3
7 5
Female
8
Male
6
Male
45
o
Joint
Male Male
Female
3 5
2 4
8 6
Female
9
Male
7
Male
45
o
Joint
2
3
Female
Male
5
4
Female
Male
PF
40mm
Cut 1
3mm
Cut 2
8mm
Cut 4
Final cut
Cut 3
40mm 28mm
Worktop
PF
30mm 20mm
Worktop
Worktop
G
Joint (35mm Inset)
35mm
Inset
35mm
Inset
90
o
90
o
Joint (35mm Inset)
Cutter
Sub base
Location pin
8.5mm
Worktop
Template
Cutter
Sub baseGuide bush Ø30mm
Location pin
8.5mm
Worktop
Template
Guide bush Ø30mm
Template
PF
PF
Cut 5
Flat Biscuit
• Ref. BSC/20/100 (Pack of 100 biscuits)
• Ref. BSC/20/1000 (Pack of 1000 biscuits)
Clamps
• Ref. FC/200
MAINTENANCE
Please use only Trend original spare parts and
accessories.
The jig has been designed to operate over a long period
of time with a minimum of maintenance. Continual
satisfactory operation depends upon proper tool care
and regular cleaning.
Cleaning
• Regularly clean the jig with a soft cloth.
Lubrication
• Your jig requires no additional lubrication.
Storage
• After use store jig in its packaging or it can be hung on
a wall hook.
• An accessory case is available, Ref. CASE/1001.
Spares
• Ref. KWJ/PIN/4
ENVIRONMENTAL PROTECTION
Recycle raw materials instead of disposing as waste.
Packaging should be sorted for environmental-friendly
recycling.
The product and its accessories at the end of their life
should be sorted for environmental friendly recycling.
WARRANTY
The jig carries a manufacturer’s warranty in accordance
with the conditions on our website www.trend-uk.com
EN - KWJ700/900
To Next Page
Loading...
