Triton TRA001 - User Manual

Other manuals for Triton TRA001

Operating And Safety Instructions12 pages

Questions and Answers

C
Charlotte MoraAug 21, 2025
Why won't my Triton TRA001 Power Tool router operate?
- M
  megan50Aug 21, 2025
  Your Triton Power Tool router might not be operating due to several reasons. First, ensure that the power is available at the source. Second, the brushes may be worn or sticking; disconnect the power, open the brush caps, and ensure the brushes move freely in their holders, checking if they need replacement. If these steps don't solve the issue, the switch or motor components could be faulty.
K
kkennedySep 3, 2025
Why does my Triton Power Tool router run or cut slowly?
- D
  Denise CisnerosSep 3, 2025
  If your Triton Power Tool router runs or cuts slowly, try the following: First, re-sharpen or replace the cutter if it's blunt or damaged. If that doesn't solve the issue, increase the variable speed setting on the Speed Controller. Lastly, reduce the pushing force on the router to avoid overloading the motor.
J
Jacob NorrisSep 1, 2025
What to do if my Triton TRA001 router will not operate?
- J
  Jennifer EvansSep 1, 2025
  If your Triton Power Tool router won't operate, first, ensure that power is available at the source. If power is available, disconnect the power, open the Brush Access Covers, and check the brushes for damage or excessive wear. If the problem persists, the switch may be faulty, and you should have the tool serviced by an authorized Triton service center.
E
ecardenasAug 30, 2025
Why can’t I plunge my Triton Power Tool to the collet lock position?
- J
  James PopeAug 31, 2025
  If you can’t plunge your Triton Power Tool to the collet lock position, it might be because the power switch is in the “On” position. Switch the power “Off” to allow plunging to the collet lock position.
J
Jason FisherAug 29, 2025
Why is the shutter on the power switch of my Triton TRA001 not releasing?
- K
  Kristina MurrayAug 29, 2025
  The shutter on the power switch of your Triton Power Tool may not be releasing because the router is plunged to full depth, in the collet lock position. Reduce the plunge depth to resolve this.
A
Ashley BradleyAug 27, 2025
What to do if my Triton TRA001 Power Tool micro adjuster “clicks”?
- K
  Katie RodriguezAug 27, 2025
  If the micro adjuster on your Triton Power Tool “clicks”, it might be because the plunge lock is engaged. Release the plunge lock lever. Alternatively, the plunge selector button may be engaged, so disengage it. Also, you may have reached the end of the adjustment range, so reset the router.
N
Nicholas NunezAug 27, 2025
What causes excessive vibration in my Triton Power Tool?
- E
  elizabeth35Aug 27, 2025
  Excessive vibration in your Triton Power Tool is likely due to a bent cutter shank. Replacing the cutter should resolve this issue.
A
Austin ReyesAug 25, 2025
Why is my Triton Power Tool router running slowly?
- H
  Holly DixonAug 25, 2025
  Your Triton Power Tool router might be running slowly because the cutter is blunt or damaged, so you should re-sharpen or replace the cutter. Another reason could be that the variable speed is set too low, so increase the variable speed setting. Also, the motor may be overloaded, so reduce the pushing force on the router.
L
Lisa GarciaAug 23, 2025
What to do if my Triton TRA001 Power Tool is making heavy sparking inside the motor housing?
- G
  gabrielacoxAug 23, 2025
  If you observe heavy sparking inside the motor housing of your Triton Power Tool, it could be due to brushes not moving freely. Disconnect the power, remove the brushes, and clean or replace them. If the problem persists, the armature could be short-circuited or open-circuited, or the commutator might be dirty.

Triton TRA001 Specifications

General

Power	1400W
No Load Speed	8000 - 21000 RPM
Voltage	230 V
Power Source	Corded Electric
Motor Power	1400W
Dust Extraction	Yes
Variable Speed	Yes
Soft Start	Yes
Collet Size	1/2" & 1/4"