25
Style Q
REF.
NO.
PART
NO. DESCRIPTION
1 731-2643 Removal Tool, Snow
2 684-04057 Impeller Assembly, 12” Dia
3 710-0347 Screw, 3/8-16 x 1.75, Gr5, Std
4 710-0451 Bolt, Carriage, 5/16-18 x.750 Gr1
5 710-0703 Screw, Carriage, 1/4-20 x .75, Gr5
6 710-0726 Screw, 5/16-12 x 0.750
7 712-04063 Nut, Flange Lock, Nylon, 5/16-18, GrF
8 712-04064 Nut, Flange Lock, Nylon, 1/4-20, GrF
9 712-04065 Nut, Flange Lock, Nylon, 3/8-16, GrF
10 714-0507 Pin, Cotter, 3/32 x .750
11 725-0157 Cable, Tie, 3/16 x .05 x 7.4
12 726-04012 Nut, Push-on, .25 Dia
13 731-04705 Chute, Adapter 5” Dia
14 732-0611 Spring, Extension, .38 OD x 3.6
15 736-0174 Washer, Wave, .625 x.885 x.015
16 736-0463 Washer, Flat, .25 x .630 x .0515
17 731-04869 Keeper, Flange
18 738-0143 Screw, Shoulder, .498 x .340, 3/8-16
19 738-0281 Screw, Shoulder, .625 x .17, 3/8-16
20 738-04124 Pin, Shear, .25 x1.50, Gr2
21 741-0245 Bearing, Hex Flange x .75 ID
22 741-0309 Bearing, Ball, .75 ID x 1.85 OD
23 756-0981A Pulley, Idler, Flat 2.75 OD
24 790-00075 Housing, Bearing, 1.85 ID
25 790-00080 Bracket, Auger Idler w/ Brake
26 631-04132 Chute Assembly, Lower, 4-way
(Inc. Ref 17, Qty. 3)
27 684-04116 Control Head (Inc. 4-Way Chute Control
Ass’y, not shown)
28 710-0262 Bolt, Carriage, 5/16-18, 1.50, Gr2
29 710-04071 Bolt, Carriage, 5/16-18, 1.00
30 710-0726 Screw, 5/16-12 x 0.75
31 710-0895 Screw, 1/4-15 x 0.75
32 710-0909A Screw, Self-tapping 5/16-18 x 1.75
33 711-0415 Pin, Clevis, 3/8 x 1.75
34 746-0897 Auger Clutch Cable, 44.75”
35 790-00091 Shoe, Slid
36 714-0104 Pin, Cotter, .072 Dia. x 1.13
37 731-04427 Upper Chute, Remote
38 731-1313C Cable Guide, Chute Tilt
39 749-04155 Support Tube, Chute
40 784-5594 Cable Bracket (Cables not included)
41 784-5599 Tab, Handle
42 618-04192 Gearbox Assembly, Auger, 26” w/ Fitting
618-04193 Gearbox Assembly, Auger, 28” w/ Fitting
43 684-04078 Housing Assembly, Auger 26”
684-04079 Housing Assembly, Auger 28”
44 684-04107 Spiral Assembly, LH
45 684-04108 Spiral Assembly, RH
46 731-04870 Spacer, 1.25 OD x .75 ID x 1.00
47 736-0188 Washer, Flat, .76 x 1.49 x .06
48 737-3000 Lube Fitting, 3/16
49 721-0179 Seal, Oil, .750 ID
50 741-0493A Bushing, Flange, .800 ID x .910 OD
51 790-00121 Plate, Shave, 2.25 x 25.66
52 790-00138 Housing, Bearing, 1” Hex
53 719-0319 Housing, Auger, RH Reducer
54 618-0418 Housing Assembly, Auger, LH Reducer
(Inc. Refs. 49 & 55)
55 741-0661A Bearing, Flange, .75 ID x 1.00 OD x .975
56 717-0528A Gear, Worm 20T
57 736-0351 Washer, Flat, .760 ID x 1.5 OD
58 714-0161 Key, Hi-pro 3/16 x 5/8
59 715-04021 Pin, Dowel, .25 OD x 1.2
60 721-0325 Plug, 1/4 x .437
61 711-04284 Axle, Auger, 26"
711-04283 Axle, Auger, 28"
62 710-0642 Screw, Self-tapping, 1/4-20, 0.750
63 741-0662 Bearing, Flange, .75 ID x 1.00 OD x .59
64 717-04126 Shaft, Worm .75 OD
65 718-04071 Collar, Thrust
66 721-0327 Seal, Oil, .75 x 1 x .131
67 736-3084 Washer, Flat, .51 x 1.12
68 741-0663 Bearing, Flange, .75 ID x 1.00 OD x .925
69 731-2635 Mount, Clean Out Tool
70 629-0071 Extension Cord, 3-Prong
71 736-0242 Washer, Bell, .340 x 872 x .060
REF.
NO.
PART
NO. DESCRIPTION
* Two found between spirals on Storm model 8526
* Three found between spirals on Storm model 9528.
To Next Page