EasyManua.ls Logo

TSC MB340 Series - User Manual

TSC MB340 Series
69 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
1
USER’S
MANUAL
MB240/ MB340/ MB240T/ MB340T Series
THERMAL TRANSFER / DIRECT THERMAL
BAR CODE PRINTER

Table of Contents

Questions and Answers

  • M
    Matthew BanksAug 19, 2025
    What to do if my TSC MB340 is not printing?
    • A
      Andrew HooverAug 19, 2025
      If your TSC printer isn't printing, try the following: * Reconnect the cable to the interface or use a new cable. * Reset the wireless device setting. * Select the correct printer port in the driver. * Clean the printhead. * Turn off the printer and plug the connector in again. * Check your program for a PRINT command at the end of the file and ensure there is CRLF at the end of each command line.
  • A
    Alicia FosterAug 21, 2025
    How to improve print quality on a TSC MB340?
    • J
      John KempAug 21, 2025
      If you're experiencing poor print quality on your TSC printer, consider these solutions: * Reload the supply. * Clean the print head and platen roller. * Adjust the print density and print speed. * Run a printer self-test and check the print head test pattern for missing dots. * Change to a proper ribbon or label media. * Adjust the printhead pressure adjustment knob. * Ensure the release lever properly latches the printhead.
  • C
    cassandra30Aug 23, 2025
    What to do when my TSC MB340 says 'No Ribbon'?
    • A
      Amanda HamiltonAug 25, 2025
      If your TSC printer indicates 'No Ribbon': * Supply a new ribbon roll. * Refer to the user’s manual for instructions on reinstalling the ribbon.
  • J
    justinmunozAug 26, 2025
    What to do if my TSC MB340 has a paper jam?
    • C
      Cathy LloydAug 26, 2025
      If your TSC printer has a paper jam, try the following: * Calibrate the media sensor. * Set the media size correctly. * Remove any stuck labels inside the printer mechanism.
  • J
    Jacob TorresAug 28, 2025
    How to fix a TSC printer when the power indicator does not illuminate?
    • R
      ramirezjosephAug 28, 2025
      If the power indicator on your TSC printer is not illuminating: * Plug the power cord into both the printer and the outlet. * Switch the printer on.
  • M
    Matthew Campbell DDSAug 30, 2025
    How to fix label feeding if it's unstable (skew) on my TSC MB340?
    • R
      Robert BergerAug 30, 2025
      If the label feeding is not stable (skew) when printing with your TSC printer: * If the label moves to the right, move the label guide to the left. * If the label moves to the left, move the label guide to the right.
  • K
    Kristi AndersonSep 1, 2025
    What to do if my TSC MB340 shows 'No Paper'?
    • R
      Robert CookSep 1, 2025
      If your TSC printer indicates 'No Paper', you should: * Supply a new label roll. * Refer to the user’s manual for instructions on reinstalling the label roll. * Calibrate the gap/black mark sensor.
  • K
    karen55Sep 3, 2025
    How to fix missing print on the sides of labels with a TSC MB340?
    • E
      egreenSep 3, 2025
      If your TSC printer is missing printing on the left or right side of the label, set the correct label size.
  • A
    ashleyatkinsonSep 5, 2025
    How to correct the printing position of small labels on a TSC MB340?
    • S
      Scott StewartSep 6, 2025
      If the printing position of a small label is incorrect on your TSC printer: * Calibrate the sensor sensitivity again. * Set the correct label size and gap size. * Press [Menu] [Setting] [Shift Y] to fine tune the parameter of Shift Y. * If using BarTender software, set the vertical offset in the driver.
  • E
    Erin CrossSep 7, 2025
    How to remove a gray line on blank labels from a TSC MB340?
    • G
      gary48Sep 7, 2025
      If there's a gray line on the blank label when using your TSC printer, clean the print head and the platen roller.

Summary

Important Safety Instructions

RF Exposure Warnings

Wi-Fi RF Exposure Warning

Warning about installation and operation to comply with RF exposure limits.

Bluetooth RF Exposure Warning

Warning about installation and operation to comply with RF exposure limits.

Canada, Industry Canada (IC) Notices

Radio Frequency (RF) Exposure Information

1.2.1 Printer Standard Features

1.3 Printer Specifications

1.4 Print Specifications

1.5 Ribbon Specifications

1.6 Media Specifications

2.3 Operator Control

2.3.1 LED Indication and Keys

2.3.3 Touch Screen

3.2 Loading the Ribbon

3.3 Remove Used Ribbon

3.4.2 Loading the Fanfold;External Media

3.4.3 Loading Media in Peel-off Mode (Option)

3.4.4 Loading Media in Cutter Mode (Option)

4. Adjustment Knob

4.1 Print Head Pressure Adjustment Knob

How to adjust print head pressure for optimal print quality based on media width.

4.2 Ribbon Tension Adjustment Knob Module

4.3 Mechanism Fine Adjustment to Avoid Ribbon Wrinkles

5. Diagnostic Tool

5.2 Printer Function

5.3 Setting Ethernet by Diagnostic Tool

5.3.1 Using USB interface to setup Ethernet interface

Step-by-step guide for configuring Ethernet settings via USB connection.

5.3.2 Using RS-232 interface to setup Ethernet interface

5.3.3 Using Ethernet interface to setup Ethernet interface

6.3.2 ZPL2

6.4 Sensor

6.5.2 Ethernet

6.5.3 Wi-Fi

6.5.4 Bluetooth

6.8 Diagnostic

Dump Mode

Print Head

7 Troubleshooting

8 Maintenance

TSC MB340 Series Specifications

General IconGeneral
BrandTSC
ModelMB340 Series
CategoryPrinter
LanguageEnglish

Related product manuals